Add a few DISAS_TARGET_* aliases to reduce the number of
calls to gen_eob() and gen_eob_inhibit_irq(). So far,
only update i386_tr_translate_insn for exiting the block
because of single-step or previous inhibit irq.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-8-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sync EIP before exiting a translation block.
Replace all gen_jmp_im that use s->pc.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-7-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like gen_update_cc_op, sync EIP before doing something
that could raise an exception. Replace all gen_jmp_im
that use s->base.pc_next.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-6-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers pass s->base.pc_next and s->pc, which we can just as
well compute within the function. Adjust to use tcg_constant_i32
while we're at it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-5-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers pass s->base.pc_next - s->cs_base, which we can just
as well compute within the function. Note the special case of
EXCP_VSYSCALL in which s->cs_base wasn't subtracted, but cs_base
is always zero in 64-bit mode, when vsyscall is used.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-4-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of returning the new pc, which is present in
DisasContext, return true if an insn was translated.
This is false when we detect a page crossing and must
undo the insn under translation.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-3-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The DisasContext member and the disas_insn local variable of
the same name are identical to DisasContextBase.pc_next.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-2-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The availability of tb->pc will shortly be conditional.
Introduce accessor functions to minimize ifdefs.
Pass around a known pc to places like tcg_gen_code,
where the caller must already have the value.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The "O" operand type in the Intel SDM needs to load an 8- to 64-bit
unsigned value, while insn_get is limited to 32 bits. Extract the code
out of disas_insn and into a separate function.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The later prefix wins if both are present, make it show in s->prefix too.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
INSERTQ is defined to not modify any bits in the lower 64 bits of the
destination, other than the ones being replaced with bits from the
source operand. QEMU instead is using unshifted bits from the source
for those bits.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many instructions which load/store 128-bit values are supposed to
raise #GP when the memory operand isn't 16-byte aligned. This includes:
- Instructions explicitly requiring memory alignment (Exceptions Type 1
in the "AVX and SSE Instruction Exception Specification" section of
the SDM)
- Legacy SSE instructions that load/store 128-bit values (Exceptions
Types 2 and 4).
This change sets MO_ALIGN_16 on 128-bit memory accesses that require
16-byte alignment. It adds cpu_record_sigbus and cpu_do_unaligned_access
hooks that simulate a #GP exception in qemu-user and qemu-system,
respectively.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/217
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ricky Zhou <ricky@rzhou.org>
Message-Id: <20220830034816.57091-2-ricky@rzhou.org>
[Do not bother checking PREFIX_VEX, since AVX is not supported. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now translator stops right *after* the end of a page, which
breaks reporting of fault locations when the last instruction of a
multi-insn translation block crosses a page boundary.
An implementation, like the one arm and s390x have, would require an
i386 length disassembler, which is burdensome to maintain. Another
alternative would be to single-step at the end of a guest page, but
this may come with a performance impact.
Fix by snapshotting disassembly state and restoring it after we figure
out we crossed a page boundary. This includes rolling back cc_op
updates and emitted ops.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1143
Message-Id: <20220817150506.592862-4-iii@linux.ibm.com>
[rth: Simplify end-of-insn cross-page checks.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Pass these along to translator_loop -- pc may be used instead
of tb->pc, and host_pc is currently unused. Adjust all targets
at one time.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The only user can easily use translator_lduw and
adjust the type to signed during the return.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
AVX includes an additional set of comparison predicates, some of which
our softfloat implementation does not expose as separate functions.
Rewrite the helpers in terms of floatN_compare for future extensibility.
Signed-off-by: Paul Brook <paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220424220204.2493824-24-paul@nowt.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a union to store the various possible kinds of function pointers, and
access the correct one based on the flags.
SSEOpHelper_table6 and SSEOpHelper_table7 right now only have one case,
but this would change with AVX's 3- and 4-argument operations. Use
unions there too, to keep the code more similar for the three tables.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For AVX we're going to need both 128 bit (xmm) and 256 bit (ymm) variants of
floating point helpers. Add the register type suffix to the existing
*PS and *PD helpers (SS and SD variants are only valid on 128 bit vectors)
No functional changes.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-15-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Put more flags to work to avoid hardcoding lists of opcodes. The op7 case
for SSE_OPF_CMP is included for homogeneity and because AVX needs it, but
it is never used by SSE or MMX.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle 3DNOW instructions early to avoid complicating the MMX/SSE logic.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-25-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a flags field each row in sse_op_table6 and sse_op_table7.
Initially this is only used as a replacement for the magic SSE41_SPECIAL
pointer. The other flags are mostly relevant for the AVX implementation
but can be applied to SSE as well.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-6-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a flags field to each row in sse_op_table1.
Initially this is only used as a replacement for the magic
SSE_SPECIAL and SSE_DUMMY pointers, the other flags are mostly
relevant for the AVX implementation but can be applied to SSE as well.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-5-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a convenience macro to get the address of an xmm_regs element within
CPUX86State.
This was originally going to be the basis of an implementation that broke
operations into 128 bit chunks. I scrapped that idea, so this is now a purely
cosmetic change. But I think a worthwhile one - it reduces the number of
function calls that need to be split over multiple lines.
No functional changes.
Signed-off-by: Paul Brook <paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220424220204.2493824-9-paul@nowt.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Write down explicitly the load/store sequence.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The correct A20 masking is done if paging is enabled (protected mode) but it
seems to have been forgotten in real mode. For example from the AMD64 APM Vol. 2
section 1.2.4:
> If the sum of the segment base and effective address carries over into bit 20,
> that bit can be optionally truncated to mimic the 20-bit address wrapping of the
> 8086 processor by using the A20M# input signal to mask the A20 address bit.
Most BIOSes will enable the A20 line on boot, but I found by disabling the A20 line
afterwards, the correct wrapping wasn't taking place.
`handle_mmu_fault' in target/i386/tcg/sysemu/excp_helper.c seems to be the culprit.
In real mode, it fills the TLB with the raw unmasked address. However, for the
protected mode, the `mmu_translate' function does the correct A20 masking.
The fix then should be to just apply the A20 mask in the first branch of the if
statement.
Signed-off-by: Stephen Michael Jothen <sjothen@gmail.com>
Message-Id: <Yo5MUMSz80jXtvt9@air-old.local>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Coverity warns that 14 << data32 may overflow with respect
to the target_ulong to which it is subsequently added.
We know this wasn't true because data32 is in [1,2],
but the suggested fix is perfectly fine.
Fixes: Coverity CID 1487135, 1487256
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-Id: <20220401184635.327423-1-richard.henderson@linaro.org>
G_NORETURN was introduced in glib 2.68, fallback to G_GNUC_NORETURN in
glib-compat.
Note that this attribute must be placed before the function declaration
(bringing a bit of consistency in qemu codebase usage).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20220420132624.2439741-20-marcandre.lureau@redhat.com>
We have fetched and locked the logfile in translator_loop.
Pass the filepointer down to the disas_log hook so that it
need not be fetched and locked again.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-13-richard.henderson@linaro.org>
Inside qemu_log, we perform qemu_log_trylock/unlock, which need
not be done if we have already performed the lock beforehand.
Always check the result of qemu_log_trylock -- only checking
qemu_loglevel_mask races with the acquisition of the lock on
the logfile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-10-richard.henderson@linaro.org>
This function can fail, which makes it more like ftrylockfile
or pthread_mutex_trylock than flockfile or pthread_mutex_lock,
so rename it.
To closer match the other trylock functions, release rcu_read_lock
along the failure path, so that qemu_log_unlock need not be called
on failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-8-richard.henderson@linaro.org>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
High bits in the immediate operand of SSE comparisons are ignored, they
do not result in an undefined opcode exception. This is mentioned
explicitly in the Intel documentation.
Reported-by: sonicadvance1@gmail.com
Closes: https://gitlab.com/qemu-project/qemu/-/issues/184
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The instruction description says "It is loaded without rounding
errors." which implies we should have the widest rounding mode
possible.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/888
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220315121251.2280317-4-alex.bennee@linaro.org>
Loading a non-canonical address into rsp when handling an interrupt or
performing a far call should raise a #SS not a #GP.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/870
Signed-off-by: Gareth Webb <gareth.webb@umbralsoftware.co.uk>
Message-Id: <164529651121.25406.15337137068584246397-0@git.sr.ht>
[Move get_pg_mode to seg_helper.c for user-mode emulators. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LA57/PKE/PKS is only relevant in 64-bit mode, and NXE is only relevant if
PAE is in use. Since there is code that checks PG_MODE_LA57 to determine
the canonicality of addresses, make sure that the bit is not set by
mistake in 32-bit mode. While it would not be a problem because 32-bit
addresses by definition fit in both 48-bit and 57-bit address spaces,
it is nicer if get_pg_mode() actually returns whether a feature is enabled,
and it allows a few simplifications in the page table walker.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
excp_helper.c requires "exec/exec-all.h" for tlb_set_page_with_attrs()
and misc_helper.c for tlb_flush().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-8-f4bug@amsat.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I think these have been wrong since f193c7979c (do not depend on
thunk.h - more log items). Fix them so as not to confuse other
debugging.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220204204335.1689602-26-alex.bennee@linaro.org>
Renaming defines for quad in their various forms so that their signedness is
now explicit.
Done using git grep as suggested by Philippe, with a bit of hand edition to
keep assignments aligned.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-2-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
