I think it's use was removed by
Commit 5883d8b296 ("mmu-hash*: Don't use full ppc_hash{32,
64}_translate() path for get_phys_page_debug()")
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Dr. David Alan Gilbert <dave@treblig.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
msgsnd has a broadcast mode that sends hypervisor doorbells to all
threads belonging to the same core as the target. A "subcore" mode
sends to all or one thread depending on 1LPAR mode.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This implements the POWER SPRC/SPRD SPRs, and SCRATCH0-7 registers that
can be accessed via these indirect SPRs.
SCRATCH registers only provide storage, but they are used by firmware
for low level crash and progress data, so this implementation logs
writes to the registers to help with analysis.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
LDBAR, TTR are a Power-specific SPRs. These simple implementations
are enough for IBM proprietary firmware for now.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
AMOR, MMCRC, HRMOR, TSCR, HMEER, RPR SPRs are per-core or per-LPAR
registers with simple (generic) implementations.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
An SPR can be either per-thread, per-core, or per-LPAR. Per-LPAR means
per-thread or per-core, depending on 1LPAR mode.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
PPR32 provides access to the upper half of PPR.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
attn is an implementation-specific instruction that on POWER (and G5/
970) can be enabled with a HID bit (disabled = illegal), and executing
it causes the host processor to stop and the service processor to be
notified. Generally used for debugging.
Implement attn and make it checkstop the system, which should be good
enough for QEMU debugging.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Change the logging not to print to stderr as well, because a
checkstop is a guest error (or perhaps a simulated machine error)
rather than a QEMU error, so send it to the log.
Update the checkstop message, and log CPU registers too.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
checkstop state does not halt the system, interrupts continue to be
serviced, and other CPUs run. Make it stop the machine with
qemu_system_guest_panicked.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
There is a memop_size() function for this.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use DEF_MEMOP() consistently in larx and stcx. generation, and apply it
once when it's used rather than where the macros are expanded, to reduce
typing.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Adds migration support for Branch History Rolling
Buffer (BHRB) internal state.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add support for the clrbhrb and mfbhrbe instructions.
Since neither instruction is believed to be critical to
performance, both instructions were implemented using helper
functions.
Access to both instructions is controlled by bits in the
HFSCR (for privileged state) and MMCR0 (for problem state).
A new function, helper_mmcr0_facility_check, was added for
checking MMCR0[BHRBA] and raising a facility_unavailable exception
if required.
NOTE: For P8 and P9, due to a performance issue, branch history will
not be kept, but the instructions will be allowed to execute
as normal with the exception that the mfbhrbe instruction will
always return a zero value.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This commit continues adding support for the Branch History
Rolling Buffer (BHRB) as is provided starting with the P8
processor and continuing with its successors. This commit
is limited to the recording and filtering of taken branches.
The following changes were made:
- Enabled functionality on P10 processors only due to
performance impact seen with P8 and P9 where it is not
disabled for non problem state branches.
- Added a BHRB buffer for storing branch instruction and
target addresses for taken branches
- Renamed gen_update_cfar to gen_update_branch_history and
added a 'target' parameter to hold the branch target
address and 'inst_type' parameter to use for filtering
- Added TCG code to gen_update_branch_history that stores
data to the BHRB and updates the BHRB offset.
- Added BHRB resource initialization and reset functions
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This commit is preparatory to the addition of Branch History
Rolling Buffer (BHRB) functionality, which is being provided
today starting with the P8 processor.
BHRB uses several SPR register fields to control whether or not
a branch instruction's address (and sometimes target address)
should be recorded. Checking each of these fields with each
branch instruction using jitted code would lead to a significant
decrease in performance.
Therefore, it was decided that BHRB configuration bits that are
not expected to change frequently should have their state summarized
in an hflag so that the amount of checking done by jitted code can
be reduced.
This commit contains the changes for summarizing the state of the
following register fields in the HFLAGS_BHRB_ENABLE hflag:
MMCR0[FCP] - Determines if BHRB recording is frozen in the
problem state
MMCR0[FCPC] - A modifier for MMCR0[FCP]
MMCRA[BHRBRD] - Disables all BHRB recording for a thread
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
v{max, min}{u, s}{b, h, w, d} : VX-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification:
v{and, andc, nand, or, orc, nor, xor, eqv} : VX-form
The changes were verified by validating that the tcp ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
{l,st}ve{b,h,w}x,
{l,st}v{x,xl},
lvs{l,r} : X-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the below instructions to decodetree specification :
andi[s]., {ori, xori}[s] : D-form
{and, andc, nand, or, orc, nor, xor, eqv}[.],
exts{b, h, w}[.], cnt{l, t}z{w, d}[.],
popcnt{b, w, d}, prty{w, d}, cmp, bpermd : X-form
With this patch, all the fixed-point logical instructions have been
moved to decodetree.
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: 32-bit compile fix]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
cmp{rb, eqb}, t{w, d} : X-form
t{w, d}i : D-form
isel : A-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Also for CMPRB, following review comments :
Replaced repetition of arithmetic right shifting (tcg_gen_shri_i32) followed
by extraction of last 8 bits (tcg_gen_ext8u_i32) with extraction of the required
bits using offsets (tcg_gen_extract_i32).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: 32-bit compile fix]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the below instructions to decodetree specification :
divd[u, e, eu][o][.] : XO-form
mod{sd, ud} : X-form
With this patch, all the fixed-point arithmetic instructions have been
moved to decodetree.
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Also, remaned do_divwe method in fixedpoint-impl.c.inc to do_dive because it is
now used to divide doubleword operands as well, and not just words.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: 32-bit compile fix]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree :
mul{ld, ldo, hd, hdu}[.] : XO-form
madd{hd, hdu, ld} : VA-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op'
flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: 32-bit compile fix]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the below instructions to decodetree specification :
neg[o][.] : XO-form
mod{sw, uw}, darn : X-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: 32-bit compile fix]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
divw[u, e, eu][o][.] : XO-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The handler methods for divw[u] instructions internally use Rc(ctx->opcode),
for extraction of Rc field of instructions, which poses a problem if we move
the above said instructions to decodetree, as the ctx->opcode field is not
popluated in decodetree. Hence, making it decodetree compatible, so that the
mentioned insns can be safely move to decodetree specs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
mulli : D-form
mul{lw, lwo, hw, hwu}[.] : XO-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Also cleaned up code for mullw[o][.] as per review comments while
keeping the logic of the tcg ops generated semantically same.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This patch moves the below instructions to decodetree specification :
f{add, sub, mul, div, re, rsqrte, madd, msub, nmadd, nmsub}[s][.] : A-form
ft{div, sqrt} : X-form
With this patch, all the floating-point arithmetic instructions have been
moved to decodetree.
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This patch merges the definitions of the following set of fpu helper methods,
which are similar, using macros :
1. f{add, sub, mul, div}(s)
2. fre(s)
3. frsqrte(s)
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER10 adds a new field to sync for store-store syncs, and some
new variants of the existing syncs that include persistent memory.
Implement the store-store syncs and plwsync/phwsync.
Reviewed-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Memory barriers are supposed to do something on BookE systems, these
were probably just missed during MTTCG enablement, maybe no targets
support SMP. Either way, add proper BookE implementations.
Reviewed-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This tries to faithfully reproduce the odd BookE logic. Note the
e206 check in gen_msync_4xx() is always false, so not carried over.
It does change the handling of non-zero reserved bits outside the
defined fields from being illegal to being ignored, which the
architecture specifies ot help with backward compatibility of new
fields. The existing behaviour causes illegal instruction exceptions
when using new POWER10 sync variants that add new fields, after this
the instructions are accepted and are implemented as supersets of
the new behaviour, as intended.
Reviewed-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
With mttcg, broadcast tlbie instructions do not wait until other vCPUs
have been kicked out of TCG execution before they complete (including
necessary subsequent tlbsync, etc., instructions). This is contrary to
the ISA, and it permits other vCPUs to use translations after the TLB
flush. For example:
CPU0
// *memP is initially 0, memV maps to memP with *pte
*pte = 0;
ptesync ; tlbie ; eieio ; tlbsync ; ptesync
*memP = 1;
CPU1
assert(*memV == 0);
It is possible for the assertion to fail because CPU1 translates memV
using the TLB after CPU0 has stored 1 to the underlying memory. This
race was observed with a careful test case where CPU1 checks run in a
very large expensive TB so it can run for the entire CPU0 period between
clearing the pte and storing the memory, but host vCPU thread preemption
could cause the race to hit anywhere.
As explained in commit 4ddc104689b ("target/ppc: Fix tlbie"), it is not
enough to just use tlb_flush_all_cpus_synced(), because that does not
execute until the calling CPU has finished its TB. It is also required
that the TB is ended at the point where the TLB flush must subsequently
take effect.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
PPC_VIRTUAL_HYPERVISOR_GET_CLASS is used in critical operations like
interrupts and TLB misses and is quite costly. Running the
kvm-unit-tests sieve program with radix MMU enabled thrashes the TCG
TLB and spends a lot of time in TLB and page table walking code. The
test takes 67 seconds to complete with a lot of time being spent in
code related to finding the vhyp class:
12.01% [.] g_str_hash
8.94% [.] g_hash_table_lookup
8.06% [.] object_class_dynamic_cast
6.21% [.] address_space_ldq
4.94% [.] __strcmp_avx2
4.28% [.] tlb_set_page_full
4.08% [.] address_space_translate_internal
3.17% [.] object_class_dynamic_cast_assert
2.84% [.] ppc_radix64_xlate
Keep a pointer to the class and avoid this lookup. This reduces the
execution time to 40 seconds.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Almost all of the disas_log implementations are identical.
Unify them within translator_loop.
Drop extra Priv/Virt logging from target/riscv.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Per https://discourse.gnome.org/t/port-your-module-from-g-memdup-to-g-memdup2-now/5538
The old API took the size of the memory to duplicate as a guint,
whereas most memory functions take memory sizes as a gsize. This
made it easy to accidentally pass a gsize to g_memdup(). For large
values, that would lead to a silent truncation of the size from 64
to 32 bits, and result in a heap area being returned which is
significantly smaller than what the caller expects. This can likely
be exploited in various modules to cause a heap buffer overflow.
Replace g_memdup() by the safer g_memdup2() wrapper.
Trivially safe because the argument was directly from sizeof.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210903174510.751630-27-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
- Extract page-protection definitions to page-protection.h
- Rework in accel/tcg in preparation of extracting TCG fields from CPUState
- More uses of get_task_state() in user emulation
- Xen refactors in preparation for adding multiple map caches (Juergen & Edgar)
- MAINTAINERS updates (Aleksandar and Bin)
-----BEGIN PGP SIGNATURE-----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=3Qkg
-----END PGP SIGNATURE-----
Merge tag 'accel-20240506' of https://github.com/philmd/qemu into staging
Accelerator patches
- Extract page-protection definitions to page-protection.h
- Rework in accel/tcg in preparation of extracting TCG fields from CPUState
- More uses of get_task_state() in user emulation
- Xen refactors in preparation for adding multiple map caches (Juergen & Edgar)
- MAINTAINERS updates (Aleksandar and Bin)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmY40CAACgkQ4+MsLN6t
# wN5drxAA1oIsuUzpAJmlMIxZwlzbICiuexgn/HH9DwWNlrarKo7V1l4YB8jd9WOg
# IKuj7c39kJKsDEB8BXApYwcly+l7DYdnAAI8Z7a+eN+ffKNl/0XBaLjsGf58RNwY
# fb39/cXWI9ZxKxsHMSyjpiu68gOGvZ5JJqa30Fr+eOGuug9Fn/fOe1zC6l/dMagy
# Dnym72stpD+hcsN5sVwohTBIk+7g9og1O/ctRx6Q3ZCOPz4p0+JNf8VUu43/reaR
# 294yRK++JrSMhOVFRzP+FH1G25NxiOrVCFXZsUTYU+qPDtdiKtjH1keI/sk7rwZ7
# U573lesl7ewQFf1PvMdaVf0TrQyOe6kUGr9Mn2k8+KgjYRAjTAQk8V4Ric/+xXSU
# 0rd7Cz7lyQ8jm0DoOElROv+lTDQs4dvm3BopF3Bojo4xHLHd3SFhROVPG4tvGQ3H
# 72Q5UPR2Jr2QZKiImvPceUOg0z5XxoN6KRUkSEpMFOiTRkbwnrH59z/qPijUpe6v
# 8l5IlI9GjwkL7pcRensp1VC6e9KC7F5Od1J/2RLDw3UQllMQXqVw2bxD3CEtDRJL
# QSZoS4d1jUCW4iAYdqh/8+2cOIPiCJ4ai5u7lSdjrIJkRErm32FV/pQLZauoHlT5
# eTPUgzDoRXVgI1X1slTpVXlEEvRNbhZqSkYLkXr80MLn5hTafo0=
# =3Qkg
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 06 May 2024 05:42:08 AM PDT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
* tag 'accel-20240506' of https://github.com/philmd/qemu: (28 commits)
MAINTAINERS: Update my email address
MAINTAINERS: Update Aleksandar Rikalo email
system: Pass RAM MemoryRegion and is_write in xen_map_cache()
xen: mapcache: Break out xen_map_cache_init_single()
xen: mapcache: Break out xen_invalidate_map_cache_single()
xen: mapcache: Refactor xen_invalidate_map_cache_entry_unlocked
xen: mapcache: Refactor xen_replace_cache_entry_unlocked
xen: mapcache: Break out xen_ram_addr_from_mapcache_single
xen: mapcache: Refactor xen_remap_bucket for multi-instance
xen: mapcache: Refactor xen_map_cache for multi-instance
xen: mapcache: Refactor lock functions for multi-instance
xen: let xen_ram_addr_from_mapcache() return -1 in case of not found entry
system: let qemu_map_ram_ptr() use qemu_ram_ptr_length()
user: Use get_task_state() helper
user: Declare get_task_state() once in 'accel/tcg/vcpu-state.h'
user: Forward declare TaskState type definition
accel/tcg: Move @plugin_mem_cbs from CPUState to CPUNegativeOffsetState
accel/tcg: Restrict cpu_plugin_mem_cbs_enabled() to TCG
accel/tcg: Restrict qemu_plugin_vcpu_exit_hook() to TCG plugins
accel/tcg: Update CPUNegativeOffsetState::can_do_io field documentation
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Extract page-protection definitions from "exec/cpu-all.h"
to "exec/page-protection.h".
The list of files requiring the new header was generated
using:
$ git grep -wE \
'PAGE_(READ|WRITE|EXEC|RWX|VALID|ANON|RESERVED|TARGET_.|PASSTHROUGH)'
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240427155714.53669-3-philmd@linaro.org>
Some targets use "default y" for boards to filter out those that require
TCG. For consistency we are switching all other targets to do the same.
Continue with PowerPC/POWER.
No changes to generated config-devices.mak files, other than
adding CONFIG_PPC to the ppc64-softmmu target.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
target/ppc/kvm.c calls out to code in hw/ppc/spapr*.c; that code is
not present and fails to link if CONFIG_PSERIES is not enabled.
Adjust kvm.c to depend on CONFIG_PSERIES instead of TARGET_PPC64,
and compile out anything that requires cap_papr, because only
the pseries machine will call kvmppc_set_papr().
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Printing a "PowerPC" in front of each CPU name is not helpful at all:
It is confusing for the users since they don't know whether they
have to specify these letters for the "-cpu" parameter, too, and
it also takes some precious space in the dense output of the CPU
entries. Let's simply remove this now and use two spaces at the
beginning of the lines for the indentation of the entries instead,
and add a "Available CPUs" in the very first line, like most other
target architectures are doing it for their CPU help output already.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The CPUBreakpoint and CPUWatchpoint structures are declared
in "hw/core/cpu.h", which contains declarations related to
CPUState and CPUClass. Some source files only require the
BP/WP definitions and don't need to pull in all CPU* API.
In order to simplify, create a new "exec/breakpoint.h" header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240418192525.97451-3-philmd@linaro.org>
'abi_ptr' is a user specific type. The system emulation
equivalent is 'target_ulong'. Use it in ppc_ldl_code()
to emphasis this is not an user emulation function.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231211212003.21686-18-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg/ files requires the following definitions:
- TARGET_LONG_BITS
- TARGET_PAGE_BITS
- TARGET_PHYS_ADDR_SPACE_BITS
- TCG_GUEST_DEFAULT_MO
The first 3 are defined in "cpu-param.h". The last one
in "cpu.h", with a bunch of definitions irrelevant for
TCG. By moving the TCG_GUEST_DEFAULT_MO definition to
"cpu-param.h", we can simplify various accel/tcg includes.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20231211212003.21686-4-philmd@linaro.org>
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
Board reset requires writing a fresh CPU state. As far as KVM is
concerned, the only thing that blocks reset is that CPU state is
encrypted; therefore, kvm_cpus_are_resettable() can simply check
if that is the case.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unify with other init_excp_FOO() in the same file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20240313213339.82071-5-philmd@linaro.org>
Hardware clears the MSR[ME] bit when delivering a machine check
interrupt, so that is what QEMU does.
The spapr environment runs in supervisor mode though, and receives
machine check interrupts after they are processed by the hypervisor,
and MSR[ME] must always be enabled in supervisor mode (otherwise it
could checkstop the system). So MSR[ME] must not be cleared when
delivering machine checks to the supervisor.
The fix to prevent supervisor mode from modifying MSR[ME] also
prevented it from re-enabling the incorrectly cleared MSR[ME] bit
when returning from handling the interrupt. Before that fix, the
problem was not very noticable with well-behaved code. So the
Fixes tag is not strictly correct, but practically they go together.
Found by kvm-unit-tests machine check tests (not yet upstream).
Fixes: 678b6f1af75ef ("target/ppc: Prevent supervisor from modifying MSR[ME]")
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
