While hyperv.rst already has all currently implemented Hyper-V
enlightenments documented, it may be unclear what is the recommended set to
achieve the best result. Add the corresponding section to the doc.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20240917160051.2637594-5-vkuznets@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'hyperv_synic' test from KVM unittests was observed to be flaky on certain
hardware (hangs sometimes). Debugging shows that the problem happens in
hyperv_sint_route_new() when the test tries to set up a new SynIC
route. The function bails out on:
if (!synic->sctl_enabled) {
goto cleanup;
}
but the test writes to HV_X64_MSR_SCONTROL just before it starts
establishing SINT routes. Further investigation shows that
synic_update() (called from async_synic_update()) happens after the SINT
setup attempt and not before. Apparently, the comment before
async_safe_run_on_cpu() in kvm_hv_handle_exit() does not correctly describe
the guarantees async_safe_run_on_cpu() gives. In particular, async worked
added to a CPU is actually processed from qemu_wait_io_event() which is not
always called before KVM_RUN, i.e. kvm_cpu_exec() checks whether an exit
request is pending for a CPU and if not, keeps running the vCPU until it
meets an exit it can't handle internally. Hyper-V specific MSR writes are
not automatically trigger an exit.
Fix the issue by simply raising an exit request for the vCPU where SynIC
update was queued. This is not a performance critical path as SynIC state
does not get updated so often (and async_safe_run_on_cpu() is a big hammer
anyways).
Reported-by: Jan Richter <jarichte@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20240917160051.2637594-4-vkuznets@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Windows with Hyper-V role enabled doesn't boot with 'hv-passthrough' when
no debugger is configured, this significantly limits the usefulness of the
feature as there's no support for subtracting Hyper-V features from CPU
flags at this moment (e.g. "-cpu host,hv-passthrough,-hv-syndbg" does not
work). While this is also theoretically fixable, 'hv-syndbg' is likely
very special and unneeded in the default set. Genuine Hyper-V doesn't seem
to enable it either.
Introduce 'skip_passthrough' flag to 'kvm_hyperv_properties' and use it as
one-off to skip 'hv-syndbg' when enabling features in 'hv-passthrough'
mode. Note, "-cpu host,hv-passthrough,hv-syndbg" can still be used if
needed.
As both 'hv-passthrough' and 'hv-syndbg' are debug features, the change
should not have any effect on production environments.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20240917160051.2637594-3-vkuznets@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Putting HYPERV_FEAT_SYNDBG entry under "#ifdef CONFIG_SYNDBG" in
'kvm_hyperv_properties' array is wrong: as HYPERV_FEAT_SYNDBG is not
the highest feature number, the result is an empty (zeroed) entry in
the array (and not a skipped entry!). hyperv_feature_supported() is
designed to check that all CPUID bits are set but for a zeroed
feature in 'kvm_hyperv_properties' it returns 'true' so QEMU considers
HYPERV_FEAT_SYNDBG as always supported, regardless of whether KVM host
actually supports it.
To fix the issue, leave HYPERV_FEAT_SYNDBG's definition in
'kvm_hyperv_properties' array, there's nothing wrong in having it defined
even when 'CONFIG_SYNDBG' is not set. Instead, put "hv-syndbg" CPU property
under '#ifdef CONFIG_SYNDBG' to alter the existing behavior when the flag
is silently skipped in !CONFIG_SYNDBG builds.
Leave an 'assert' sentinel in hyperv_feature_supported() making sure there
are no 'holes' or improperly defined features in 'kvm_hyperv_properties'.
Fixes: d8701185f40c ("hw: hyperv: Initial commit for Synthetic Debugging device")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20240917160051.2637594-2-vkuznets@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM commit 191c8137a939 ("x86/kvm: Implement HWCR support")
introduced support for emulating HWCR MSR.
Add support for QEMU to save/load this MSR for migration purposes.
Signed-off-by: Gao Shiyuan <gaoshiyuan@baidu.com>
Signed-off-by: Wang Liang <wangliang44@baidu.com>
Link: https://lore.kernel.org/r/20241009095109.66843-1-gaoshiyuan@baidu.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Following 5 bits in CPUID.7.2.EDX are supported by KVM. Add their
supports in QEMU. Each of them indicates certain bits of IA32_SPEC_CTRL
are supported. Those bits can control CPU speculation behavior which can
be used to defend against side-channel attacks.
bit0: intel-psfd
if 1, indicates bit 7 of the IA32_SPEC_CTRL MSR is supported. Bit 7 of
this MSR disables Fast Store Forwarding Predictor without disabling
Speculative Store Bypass
bit1: ipred-ctrl
If 1, indicates bits 3 and 4 of the IA32_SPEC_CTRL MSR are supported.
Bit 3 of this MSR enables IPRED_DIS control for CPL3. Bit 4 of this
MSR enables IPRED_DIS control for CPL0/1/2
bit2: rrsba-ctrl
If 1, indicates bits 5 and 6 of the IA32_SPEC_CTRL MSR are supported.
Bit 5 of this MSR disables RRSBA behavior for CPL3. Bit 6 of this MSR
disables RRSBA behavior for CPL0/1/2
bit3: ddpd-u
If 1, indicates bit 8 of the IA32_SPEC_CTRL MSR is supported. Bit 8 of
this MSR disables Data Dependent Prefetcher.
bit4: bhi-ctrl
if 1, indicates bit 10 of the IA32_SPEC_CTRL MSR is supported. Bit 10
of this MSR enables BHI_DIS_S behavior.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Link: https://lore.kernel.org/r/20240919051011.118309-1-chao.gao@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When user sets tsc-frequency explicitly, the invtsc feature is actually
migratable because the tsc-frequency is supposed to be fixed during the
migration.
See commit d99569d9d856 ("kvm: Allow invtsc migration if tsc-khz
is set explicitly") for referrence.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20240814075431.339209-10-xiaoyao.li@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- CPUID.(EAX=07H,ECX=0H):EBX[bit 6]: x87 FPU Data Pointer updated only
on x87 exceptions if 1.
- CPUID.(EAX=07H,ECX=0H):EBX[bit 13]: Deprecates FPU CS and FPU DS
values if 1. i.e., X87 FCS and FDS are always zero.
Define names for them so that they can be exposed to guest with -cpu host.
Also define the bit field MACROs so that named cpu models can add it as
well in the future.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20240814075431.339209-3-xiaoyao.li@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, QEMU always constructs a all-zero CPUID entry for
CPUID[0xD 0x3f].
It's meaningless to construct such a leaf as the end of leaf 0xD. Rework
the logic of how subleaves of 0xD are constructed to get rid of such
all-zero value of subleaf 0x3f.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20240814075431.339209-2-xiaoyao.li@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Filtering pending messages when a new scanout is given shouldn't discard
pending cursor changes, for example.
Since filtering happens in a different thread, use atomic set/get.
Fixes: fa88b85dea ("ui/dbus: filter out pending messages when scanout")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-ID: <20241008125028.1177932-6-marcandre.lureau@redhat.com>
(cherry picked from commit cf59889781297a5618f1735a5f31402caa806b42)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
DisplaySurface may be free before the pixman image is freed, since the
image is refcounted and used by different objects, including pending
dbus messages.
Furthermore, setting the destroy function in
create_displaysurface_from() isn't appropriate, as it may not be used,
and may be overriden as in ramfb.
Set the destroy function when the shared handle is set, use the HANDLE
directly for destroy data, using a single common helper
qemu_pixman_win32_image_destroy().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-ID: <20241008125028.1177932-5-marcandre.lureau@redhat.com>
(cherry picked from commit 330ef31deb2e5461cff907488b710f5bd9cd2327)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A filter function that wants to drop a message should return NULL, in
which case it must also unref the message itself.
Fixes: fa88b85de ("ui/dbus: filter out pending messages when scanout")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-ID: <20241008125028.1177932-4-marcandre.lureau@redhat.com>
(cherry picked from commit 244d52ff736fefc3dd364ed091720aa896af306d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When SET_STREAM_FORMAT is called, we should clear the existing setup.
Factor out common function to close a stream.
Direct leak of 144 byte(s) in 3 object(s) allocated from:
#0 0x7f91d38f7350 in calloc (/lib64/libasan.so.8+0xf7350) (BuildId: a4ad7eb954b390cf00f07fa10952988a41d9fc7a)
#1 0x7f91d2ab7871 in g_malloc0 (/lib64/libglib-2.0.so.0+0x64871) (BuildId: 36b60dbd02e796145a982d0151ce37202ec05649)
#2 0x562fa2f447ee in timer_new_full /home/elmarco/src/qemu/include/qemu/timer.h:538
#3 0x562fa2f4486f in timer_new /home/elmarco/src/qemu/include/qemu/timer.h:559
#4 0x562fa2f448a9 in timer_new_ns /home/elmarco/src/qemu/include/qemu/timer.h:577
#5 0x562fa2f47955 in hda_audio_setup ../hw/audio/hda-codec.c:490
#6 0x562fa2f4897e in hda_audio_command ../hw/audio/hda-codec.c:605
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-ID: <20241008125028.1177932-3-marcandre.lureau@redhat.com>
(cherry picked from commit 6d6e23361fc732e4fe36a8bc5873b85f264ed53a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Nothing in LoongArch fw_cfg.c requires target specific definitions.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240927213254.17552-3-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240927213254.17552-2-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Variable env->cf[i] is defined as bool type, it is treated as int type
with shift operation. However the max possible width is 56 for the shift
operation, exceeding the width of int type. And there is existing api
read_fcc() which is converted to u64 type with bitwise shift, it can be
used to dump fp registers into coredump note segment.
Resolves: Coverity CID 1561133
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240914064645.2099169-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
ACPI ged is used for power management on LoongArch virt platform, in
general it is parsed from acpi table. However if system boot directly from
elf kernel, no UEFI bios is provided and acpi table cannot be used also.
Here acpi ged pm register is exposed with FDT table, it is compatbile
with syscon method in FDT table, only that acpi ged pm register is accessed
with 8-bit mode, rather with 32-bit mode.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Tested-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240918014206.2165821-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Macro definition is added for acpi sleep control register, ged emulation
driver can use the macro , also it can be used in FDT table if ged is
exposed with FDT table.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20240918014206.2165821-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
In commit b88cfee90268cad we defined masks for the IBRD and FBRD
integer and fractional baud rate divider registers, to prevent the
guest from writing invalid values which could cause division-by-zero.
Unfortunately we got the mask values the wrong way around: the FBRD
register is six bits and the IBRD register is 16 bits, not
vice-versa.
You would only run into this bug if you programmed the UART to a baud
rate of less than 9600, because for 9600 baud and above the IBRD
value will fit into 6 bits, as per the table in
https://developer.arm.com/documentation/ddi0183/g/programmers-model/register-descriptions/fractional-baud-rate-register--uartfbrd
The only visible effects would be that the value read back from
the register by the guest would be truncated, and we would
print an incorrect baud rate in the debug logs.
Cc: qemu-stable@nongnu.org
Fixes: b88cfee90268 ("hw/char/pl011: Avoid division-by-zero in pl011_get_baudrate()")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2610
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20241007144732.2491331-1-peter.maydell@linaro.org
(cherry picked from commit cd247eae16ab1b9ce97fd34c000c1b883feeda45)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The result of 1 << regbit with regbit==31 has a 1 in the 32nd bit.
When cast to uint64_t (for further bitwise OR), the 32 most
significant bits will be filled with 1s. However, the documentation
states that the upper 32 bits of ICH_AP[0/1]R<n>_EL2 are reserved.
Add an explicit cast to match the documentation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: c3f21b065a ("hw/intc/arm_gicv3_cpuif: Support vLPIs")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 3db74afec3ca87f81fbdf5918ed1e21d837fbfab)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The result of 1 << regbit with regbit==31 has a 1 in the 32nd bit.
When cast to uint64_t (for further bitwise OR), the 32 most
significant bits will be filled with 1s. However, the documentation
states that the upper 32 bits of ICC_AP[0/1]R<n>_EL2 are reserved.
Add an explicit cast to match the documentation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: 28cca59c46 ("hw/intc/arm_gicv3: Add NMI handling CPU interface registers")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 12dc8f6eca1ead876142fd3d6731cf3da1295f2a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The result of 1 << regbit with regbit==31 has a 1 in the 32nd bit.
When cast to uint64_t (for further bitwise OR), the 32 most
significant bits will be filled with 1s. However, the documentation
states that the upper 32 bits of ICH_AP[0/1]R<n>_EL2 are reserved.
Add an explicit cast to match the documentation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: d2c0c6aab6 ("hw/intc/arm_gicv3: Handle icv_nmiar1_read() for icc_nmiar1_read()")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit e0c0ea6eca4f210a52b9742817586cc97b1ee434)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
mips_cpu_create_with_clock() creates a vCPU. Pass it the vCPU
endianness requested by argument. Update the board call sites.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-17-philmd@linaro.org>
Have the CPS expose a 'cpu-big-endian' property so it can
set it to the vCPUs it creates.
Note, since the number of vCPUs created is dynamic, we can
not use QOM aliases.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-16-philmd@linaro.org>
Add the "big-endian" property and set the CP0C0_BE bit in CP0_Config0.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-15-philmd@linaro.org>
Directly use tcg_constant_tl() for constant integer, this
save a call to tcg_gen_movi_tl(), often saving a temp register.
Most of the places found using the following Coccinelle spatch script:
@@
identifier tmp;
constant val;
@@
* TCGv tmp = tcg_temp_new();
...
* tcg_gen_movi_tl(tmp, val);
@@
identifier tmp;
int val;
@@
* TCGv tmp = tcg_temp_new();
...
* tcg_gen_movi_i64(tmp, val);
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004202621.4321-2-philmd@linaro.org>
Replace tcg_gen_movi_tl() + gen_op_addr_add() by a single
gen_op_addr_addi() call.
gen_op_addr_addi() calls tcg_gen_addi_tl() which might
optimize if the immediate is zero.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-13-philmd@linaro.org>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-12-philmd@linaro.org>
Introduce mo_endian() which returns the endian MemOp
corresponding to the vCPU DisasContext.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-10-philmd@linaro.org>
MEMOP_IDX() is unused since commit 948f88661c6 ("target/mips:
Use cpu_*_data_ra for msa load/store"), remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241014232235.51988-1-philmd@linaro.org>
In commit 6d0cad12594 ("target/mips: Finish conversion to
tcg_gen_qemu_{ld,st}_*") we renamed the argument of the user
definition. Rename the system part for coherency. Since the
argument is ignored, prefix with 'ignored_'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-9-philmd@linaro.org>
Extract the implicit MO_TE definition in order to replace
it by runtime variable in the next commit.
Mechanical change using:
$ for n in UW UL UQ UO SW SL SQ; do \
sed -i -e "s/MO_TE$n/MO_TE | MO_$n/" \
$(git grep -l MO_TE$n target/mips); \
done
manually remove superfluous parenthesis in nanoMIPS gen_save().
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-8-philmd@linaro.org>
Instead of swapping the reversed target endianness
using MO_BSWAP, directly return the correct endianness.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-7-philmd@linaro.org>
Functions are easier to rework than macros. Besides,
there is no gain here in inlining these.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-6-philmd@linaro.org>
Replace compile-time MO_TE evaluation by runtime mo_endian_env()
one, which expand target endianness from vCPU env.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-5-philmd@linaro.org>
Introduce mo_endian_env() which returns the endian
MemOp corresponding to the vCPU env.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-4-philmd@linaro.org>
Methods using the 'cpu_' prefix usually take a (Arch)CPUState
argument. Since this method takes a DisasContext argument,
rename it as disas_is_bigendian().
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-3-philmd@linaro.org>
In order to re-use cpu_is_bigendian(), declare it on "internal.h"
after renaming it as mips_env_is_bigendian().
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-2-philmd@linaro.org>
Move code evaluation from preprocessor to compiler so
both if() ladders are processed. Mostly style change.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-Id: <20240930073450.33195-8-philmd@linaro.org>
Directly use tcg_constant_tl() for constant integer,
this save a call to tcg_gen_movi_tl() and a temp register.
Inspired-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004202621.4321-4-philmd@linaro.org>
Directly use tcg_constant_tl() for constant integer,
this save a call to tcg_gen_movi_tl().
Inspired-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004202621.4321-3-philmd@linaro.org>
The TriCore architecture uses little endianness. Directly use
the little-endian LD/ST API.
Mechanical change using:
$ end=le; \
for acc in uw w l q tul; do \
sed -i -e "s/ld${acc}_p(/ld${acc}_${end}_p(/" \
-e "s/st${acc}_p(/st${acc}_${end}_p(/" \
$(git grep -wlE '(ld|st)t?u?[wlq]_p' target/tricore/); \
done
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004163042.85922-15-philmd@linaro.org>
The LoongArch architecture uses little endianness. Directly
use the little-endian LD/ST API.
Mechanical change using:
$ end=le; \
for acc in uw w l q tul; do \
sed -i -e "s/ld${acc}_p(/ld${acc}_${end}_p(/" \
-e "s/st${acc}_p(/st${acc}_${end}_p(/" \
$(git grep -wlE '(ld|st)t?u?[wlq]_p' target/loongarch/); \
done
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004163042.85922-13-philmd@linaro.org>
The x86 architecture uses little endianness. Directly use
the little-endian LD/ST API.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20241003234211.53644-4-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The AVR architecture uses little endianness. Directly use
the little-endian LD/ST API.
Mechanical change using:
$ end=le; \
for acc in uw w l q tul; do \
sed -i -e "s/ld${acc}_p(/ld${acc}_${end}_p(/" \
-e "s/st${acc}_p(/st${acc}_${end}_p(/" \
$(git grep -wlE '(ld|st)t?u?[wlq]_p' target/avr/); \
done
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241004163042.85922-11-philmd@linaro.org>
