Add basic USB PHY support as implemented in i.MX23, i.MX28, i.MX6,
and i.MX7 SoCs.
The only support really needed - at least to boot Linux - is support
for soft reset, which needs to reset various registers to their initial
value. Otherwise, just record register values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200313014551.12554-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux guests wait ~30 seconds when closing the emulated /dev/ttyUSB0.
During that time, the kernel driver is sending many control URBs
requesting GetModemStat (5). Real hardware returns a status with
FTDI_THRE (Transmitter Holding Register) and FTDI_TEMT (Transmitter
Empty) set. QEMU leaves them clear, and it seems Linux is waiting for
FTDI_TEMT to be set to indicate the tx queue is empty before closing.
Set the bits when responding to a GetModemStat query and avoid the
shutdown delay.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20200316174610.115820-5-jandryuk@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
A FTDI USB adapter on an xHCI controller can send 512 byte USB packets.
These are 8 * ( 2 bytes header + 62 bytes data). A 384 byte receive
buffer is insufficient to fill a 512 byte packet, so bump the receive
size to 496 ( 512 - 2 * 8 ).
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20200316174610.115820-4-jandryuk@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-serial has issues with xHCI controllers where data is lost in the
VM. Inspecting the URBs in the guest, EHCI starts every 64 byte boundary
(wMaxPacketSize) with a header. EHCI hands packets into
usb_serial_token_in() with size 64, so these cannot cross the 64 byte
boundary. The xHCI controller has packets of 512 bytes and the usb-serial
will just write through the 64 byte boundary. In the guest, this means
data bytes are interpreted as header, so data bytes don't make it out
the serial interface.
Re-work usb_serial_token_in to chunk data into 64 byte units - 2 byte
header and 62 bytes data. The Linux driver reads wMaxPacketSize to find
the chunk size, so we match that.
Real hardware was observed to pass in 512 byte URBs (496 bytes data +
8 * 2 byte headers). Since usb-serial only buffers 384 bytes of data,
usb-serial will pass in 6 64 byte blocks and 1 12 byte partial block for
462 bytes max.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Message-id: 20200316174610.115820-3-jandryuk@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We'll be adding a loop, so move the code into a helper function. breaks
are replaced with returns. While making this change, add braces to
single line if statements to comply with coding style and keep
checkpatch happy.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Message-id: 20200316174610.115820-2-jandryuk@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Linux kernels call "ibm,nmi-interlock" in their system reset handlers
contrary to PAPR. Returning an error because the CPU does not hold the
interlock here causes Linux to print warning messages. PowerVM returns
success in this case, so do the same for now.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-9-npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PAPR requires that if "ibm,nmi-register" succeeds, then the hypervisor
delivers all system reset and machine check exceptions to the registered
addresses.
System Resets are delivered with registers set to the architected state,
and with no interlock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-8-npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide for an alternate delivery location, -1 defaults to the
architected address.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-7-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There should no longer be a reason to prevent TCG providing FWNMI.
System Reset interrupts are generated to the guest with nmi monitor
command and H_SIGNAL_SYS_RESET. Machine Checks can not be injected
currently, but this could be implemented with the mce monitor cmd
similarly to i386.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-6-npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
[dwg: Re-enable FWNMI in qtests, since that now works]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
FWNMI machine check delivery misses a few things that will make it fail
with TCG at least (which we would like to allow in future to improve
testing).
It's not nice to scatter interrupt delivery logic around the tree, so
move it to excp_helper.c and share code where possible.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-5-npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The FWNMI option must deliver system reset interrupts to their
registered address, and there are a few constraints on the handler
addresses specified in PAPR. Add the system reset address state and
checks.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-4-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviwed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The option is called "FWNMI", and it involves more than just machine
checks, also machine checks can be delivered without the FWNMI option,
so re-name various things to reflect that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-3-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ppc_cpu_do_system_reset delivers a system rreset interrupt to the guest,
which is certainly not what is intended here. Panic the guest like other
failure cases here do.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200316142613.121089-2-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In the spapr code we've been gradually moving towards a convention that
functions which create pieces of the device tree are called spapr_dt_*().
This patch speeds that along by renaming most of the things that don't yet
match that so that they do.
For now we leave the *_dt_populate() functions which are actual methods
used in the DRCClass::dt_populate method.
While we're there we remove a few comments that don't really say anything
useful.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This is currently called from spapr_dt_cas_updates() which is a hang
over from when we created this only as a diff to the DT at CAS time.
Now that we fully rebuild the DT at CAS time, just create it along
with the rest of the properties in /chosen.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently this node with information about hotpluggable memory is created
from spapr_dt_cas_updates(). But that's just a hangover from when we
created it only as a diff to the device tree at CAS time. Now that we
fully rebuild the DT as CAS time, it makes more sense to create this along
with the rest of the memory information in the device tree.
So, move it to spapr_populate_memory(). The patch is huge, but it's nearly
all just code motion.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
At the moment SLOF reserves space for RTAS and instantiates the RTAS blob
which is 20 bytes binary blob calling an hypercall. The rest of the RTAS
area is a log which SLOF has no idea about but QEMU does.
This moves RTAS sizing to QEMU and this overrides the size from SLOF.
The only remaining problem is that SLOF copies the number of bytes it
reserved (2KB for now) so QEMU needs to reserve at least this much;
SLOF will be fixed separately to check that rtas-size from QEMU is
enough for those 20 bytes for the H_RTAS hcall.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20200316011841.99970-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At the moment "pseries" starts in SLOF which only expects the FDT blob
pointer in r3. As we are going to introduce a OpenFirmware support in
QEMU, we will be booting OF clients directly and these expect a stack
pointer in r1, Linux looks at r3/r4 for the initramdisk location
(although vmlinux can find this from the device tree but zImage from
distro kernels cannot).
This extends spapr_cpu_set_entry_state() to take more registers. This
should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20200310050733.29805-2-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "ibm,xive-lisn-ranges" defines ranges of interrupt numbers that
the guest can use to configure IPIs. It starts at 0 today but it could
change to some other offset. Make clear which IRQ range we are
exposing by using SPAPR_IRQ_IPI in the property definition.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200306123307.1348-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-8-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Depending on the length of sense data, vscsi_send_rsp() can
overrun the buffer size.
Do not copy more than SRP_MAX_IU_DATA_LEN bytes, and assert
that vscsi_send_iu() is always called with a size in range.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-7-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'union srp_iu' is meant as a pointer to any SRP Information
Unit type, it is not related to the size of a VIO DMA buffer.
Use a plain buffer for the VIO DMA read/write calls.
We can remove the reserved buffer from the 'union srp_iu'.
This issue was noticed when replacing the zero-length arrays
from hw/scsi/srp.h with flexible array member,
'clang -fsanitize=undefined' reported:
hw/scsi/spapr_vscsi.c:69:29: error: field 'iu' with variable sized type 'union viosrp_iu' not at the end of a struct or class is a GNU extension [-Werror,-Wgnu-variable-sized-type-not-at-end]
union viosrp_iu iu;
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-6-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce the req_iu() helper which returns a pointer to
the viosrp_iu union held in the vscsi_req structure.
This simplifies the next patch.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-5-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We already have a 'iu' pointer, use it
(this simplifies the next commit).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-4-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace sizeof() flexible arrays union srp_iu/viosrp_iu by the
SRP_MAX_IU_LEN definition, which is what this code actually meant
to use.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-3-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This header use the srp_* structures declared in "hw/scsi/srp.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-2-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move the calculation of the Real Mode Area (RMA) size into a helper
function. While we're there clean it up and correct it in a few ways:
* Add comments making it clearer where the various constraints come from
* Remove a pointless check that the RMA fits within Node 0 (we've just
clamped it so that it does)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The existing code uses fixed PCI IRQ routing on IRQ 14 rather than legacy IRQ
14/15 routing as documented in the datasheet.
With the changes in this patchset guest OSs now correctly detect and configure
the VIA controller in legacy IRQ routing mode, allowing the incorrect fixed
PCI IRQ routing to be removed.
Note that this fixed legacy IRQ 14/15 routing is identical to similar behaviour
in the early PIIX IDE controllers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-8-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
MorphOS writes to PCI_CLASS_PROG during IDE initialisation to place the
controller in native mode, but thinks the initialisation has failed
because the native mode bits aren't set when reading the register back.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-7-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
According to both the VT82C686B and VT8231 datasheets the VIA Southbridge IDE
controller is initialised in legacy mode.
This allows Linux to correctly determine that legacy rather than PCI IRQ routing
should be used since the boot console text in the fulong2e test image changes from:
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0xffffffffbfd04050 ctl 0xffffffffbfd04062 \
bmdma 0xffffffffbfd04040 irq 14
ata2: PATA max UDMA/100 cmd 0xffffffffbfd04058 ctl 0xffffffffbfd04066 \
bmdma 0xffffffffbfd04048 irq 14
to:
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0xffffffffbfd001f0 ctl 0xffffffffbfd003f6 \
bmdma 0xffffffffbfd04040 irq 14
ata2: PATA max UDMA/100 cmd 0xffffffffbfd00170 ctl 0xffffffffbfd00376 \
bmdma 0xffffffffbfd04048 irq 15
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-6-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Some firmwares accidentally write to PCI_INTERRUPT_LINE on startup which has
no effect on real hardware since it is hard-wired to its default value, but
causes the guest OS to become confused trying to initialise IDE devices
when running under QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-5-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
The pci_do_device_reset() function (called from pci_device_reset)
clears the PCI_INTERRUPT_LINE config reg of devices on the bus but did
this without taking wmask into account. We'll have a device model now
that needs to set a constant value for this reg and this patch allows
to do that without additional workaround in device emulation to
reverse the effect of this PCI bus reset function.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200313082444.2439-4-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Follow example of CMD646 and remove via_ide_init function and do it
directly in board code instead.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200313082444.2439-3-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Update BIOS_FILENAME to consider 32-bit bios image file name.
Tested booting Linux v5.5 32-bit image (built from rv32_defconfig
plus CONFIG_SOC_SIFIVE) with the default 32-bit bios image.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
In spapr_machine_init() we clamp the size of the RMA to 16GiB and the
comment saying why doesn't make a whole lot of sense. In fact, this was
done because the real mode handling code elsewhere limited the RMA in TCG
mode to the maximum value configurable in LPCR[RMLS], 16GiB.
But,
* Actually LPCR[RMLS] has been able to encode a 256GiB size for a very
long time, we just didn't implement it properly in the softmmu
* LPCR[RMLS] shouldn't really be relevant anyway, it only was because we
used to abuse the RMOR based translation mode in order to handle the
fact that we're not modelling the hypervisor parts of the cpu
We've now removed those limitations in the modelling so the 16GiB clamp no
longer serves a function. However, we can't just remove the limit
universally: that would break migration to earlier qemu versions, where
the 16GiB RMLS limit still applies, no matter how bad the reasons for it
are.
So, we replace the 16GiB clamp, with a clamp to a limit defined in the
machine type class. We set it to 16 GiB for machine types 4.2 and earlier,
but set it to 0 meaning unlimited for the new 5.0 machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Real Mode Area (RMA) is the part of memory which a guest can access
when in real (MMU off) mode. Of course, for a guest under KVM, the MMU
isn't really turned off, it's just in a special translation mode - Virtual
Real Mode Area (VRMA) - which looks like real mode in guest mode.
The mechanics of how this works when using the hash MMU (HPT) put a
constraint on the size of the RMA, which depends on the size of the
HPT. So, the latter part of spapr_setup_hpt_and_vrma() clamps the RMA
we advertise to the guest based on this VRMA limit.
There are several things wrong with this:
1) spapr_setup_hpt_and_vrma() doesn't actually clamp, it takes the minimum
of Node 0 memory size and the VRMA limit. That will *often* work the
same as clamping, but there can be other constraints on RMA size which
supersede Node 0 memory size. We have real bugs caused by this
(currently worked around in the guest kernel)
2) Some callers of spapr_setup_hpt_and_vrma() are in a situation where
we're past the point that we can actually advertise an RMA limit to the
guest
3) But most fundamentally, the VRMA limit depends on host configuration
(page size) which shouldn't be visible to the guest, but this partially
exposes it. This can cause problems with migration in certain edge
cases, although we will mostly get away with it.
In practice, this clamping is almost never applied anyway. With 64kiB
pages and the normal rules for sizing of the HPT, the theoretical VRMA
limit will be 4x(guest memory size) and so never hit. It will hit with
4kiB pages, where it will be (guest memory size)/4. However all mainstream
distro kernels for POWER have used a 64kiB page size for at least 10 years.
So, simply replace this logic with a check that the RMA we've calculated
based only on guest visible configuration will fit within the host implied
VRMA limit. This can break if running HPT guests on a host kernel with
4kiB page size. As noted that's very rare. There also exist several
possible workarounds:
* Change the host kernel to use 64kiB pages
* Use radix MMU (RPT) guests instead of HPT
* Use 64kiB hugepages on the host to back guest memory
* Increase the guest memory size so that the RMA hits one of the fixed
limits before the RMA limit. This is relatively easy on POWER8 which
has a 16GiB limit, harder on POWER9 which has a 1TiB limit.
* Use a guest NUMA configuration which artificially constrains the RMA
within the VRMA limit (the RMA must always fit within Node 0).
Previously, on KVM, we also temporarily reduced the rma_size to 256M so
that the we'd load the kernel and initrd safely, regardless of the VRMA
limit. This was a) confusing, b) could significantly limit the size of
images we could load and c) introduced a behavioural difference between
KVM and TCG. So we remove that as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
This function calculates the maximum size of the RMA as implied by the
host's page size of structure of the VRMA (there are a number of other
constraints on the RMA size which will supersede this one in many
circumstances).
The current interface takes the current RMA size estimate, and clamps it
to the VRMA derived size. The only current caller passes in an arguably
wrong value (it will match the current RMA estimate in some but not all
cases).
We want to fix that, but for now just keep concerns separated by having the
KVM helper function just return the VRMA derived limit, and let the caller
combine it with other constraints. We call the new function
kvmppc_vrma_limit() to more clearly indicate its limited responsibility.
The helper should only ever be called in the KVM enabled case, so replace
its !CONFIG_KVM stub with an assert() rather than a dummy value.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
MIN_RMA_SLOF records the minimum about of RMA that the SLOF firmware
requires. It lets us give a meaningful error if the RMA ends up too small,
rather than just letting SLOF crash.
It's currently stored as a number of megabytes, which is strange for global
constants. Move that megabyte scaling into the definition of the constant
like most other things use.
Change from M to MiB in the associated message while we're at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
For the "pseries" machine, we use "virtual hypervisor" mode where we
only model the CPU in non-hypervisor privileged mode. This means that
we need guest physical addresses within the modelled cpu to be treated
as absolute physical addresses.
We used to do that by clearing LPCR[VPM0] and setting LPCR[RMLS] to a high
limit so that the old offset based translation for guest mode applied,
which does what we need. However, POWER9 has removed support for that
translation mode, which meant we had some ugly hacks to keep it working.
We now explicitly handle this sort of translation for virtual hypervisor
mode, so the hacks aren't necessary. We don't need to set VPM0 and RMLS
from the machine type code - they're now ignored in vhyp mode. On the cpu
side we don't need to allow LPCR[RMLS] to be set on POWER9 in vhyp mode -
that was only there to allow the hack on the machine side.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200228123303.14540-1-philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fixes Coverity issue,
CID 1419883: Error handling issues (CHECKED_RETURN)
Calling "qemu_uuid_parse" without checking return value
nvdimm_set_uuid() already verifies if the user provided uuid is valid or
not. So, need to check for the validity during pre-plug validation again.
As this a false positive in this case, assert if not valid to be safe.
Also, error_abort if QOM accessor encounters error while fetching the uuid
property.
Reported-by: Coverity (CID 1419883)
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Message-Id: <158281096564.89540.4507375445765515529.stgit@lep8c.aus.stglabs.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a hot plug or unplug request is pending at CAS, we currently trigger
a CAS reboot, which severely increases the guest boot time. This is
because SLOF doesn't handle hot plug events and we had no way to fix
the FDT that gets presented to the guest.
We can do better thanks to recent changes in QEMU and SLOF:
- we now return a full FDT to SLOF during CAS
- SLOF was fixed to correctly detect any device that was either added or
removed since boot time and to update its internal DT accordingly.
The right solution is to process all pending hot plug/unplug requests
during CAS: convert hot plugged devices to cold plugged devices and
remove the hot unplugged ones, which is exactly what spapr_drc_reset()
does. Also clear all hot plug events that are currently queued since
they're no longer relevant.
Note that SLOF cannot currently populate hot plugged PCI bridges or PHBs
at CAS. Until this limitation is lifted, SLOF will reset the machine when
this scenario occurs : this will allow the FDT to be fully processed when
SLOF is started again (ie. the same effect as the CAS reboot that would
occur anyway without this patch).
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158257222352.4102917.8984214333937947307.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 355477f8c73e9 skips rom reset when we're an incoming migration
so as not to overwrite shared ram in the ignore-shared migration
optimisation.
However, it's got an unexpected side effect that because it skips
freeing the ROM data, when rom_reset gets called later on, after
migration (e.g. during a reboot), the ROM does get reset to the original
file contents. Because of seabios/x86's weird reboot process
this confuses a reboot into hanging after a migration.
Fixes: 355477f8c73e9 ("migration: do not rom_reset() during incoming migration")
https://bugzilla.redhat.com/show_bug.cgi?id=1809380
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The USB descriptor sizes are specified as 16-bit for idVendor /
idProduct, and 8-bit for bInterfaceClass / bInterfaceSubClass /
bInterfaceProtocol. Doing so we reduce the usbredir_raw_serial_ids[]
and usbredir_ftdi_serial_ids[] arrays from 16KiB to 6KiB (size
reported on x86_64 host, building with --extra-cflags=-Os).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The intel-hda model uses an array of register indexed by the
register address. This array also contains a pair of aliased
registers at offset 0x2000. This creates a huge hole in the
array, which ends up eating 4.6MiB of .rodata (size reported
on x86_64 host, building with --extra-cflags=-Os).
By using a memory region alias, we reduce this array to 132kB.
Before:
(qemu) info mtree
00000000febd4000-00000000febd7fff (prio 1, i/o): intel-hda
After:
(qemu) info mtree
00000000febd4000-00000000febd7fff (prio 1, i/o): intel-hda
00000000febd4000-00000000febd7fff (prio 1, i/o): intel-hda-container
00000000febd4000-00000000febd5fff (prio 0, i/o): intel-hda
00000000febd6000-00000000febd7fff (prio 0, i/o): alias intel-hda-alias @intel-hda 0000000000000000-0000000000001fff
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This buffer is only used by the adlib audio device. Move it to
the .heap to release 32KiB of .bss (size reported on x86_64 host).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several objects implemented their own uint property getters and setters,
despite them being straightforward (without any checks/validations on
the values themselves) and identical across objects. This makes use of
an enhanced API for object_property_add_uintXX_ptr() which offers
default setters.
Some of these setters used to update the value even if the type visit
failed (eg. because the value being set overflowed over the given type).
The new setter introduces a check for these errors, not updating the
value if an error occurred. The error is propagated.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, ich9_lpc_initfn simply serves as a caller to
ich9_lpc_add_properties. This simplifies the code a bit by eliminating
ich9_lpc_add_properties altogether and executing its logic in the parent
object initialiser function.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When QOM APIs were added to ich9 in 6f1426ab, the getter for sci_int was
written using uint32_t. However, the object property is uint8_t. This
fixes the getter for correctness.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
