A Write Zeroes commands should not be counted in either the 'Data Units
Written' or in 'Host Write Commands' SMART/Health Information Log page.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The 'len' member of the nvme_compare_ctx struct is redundant since the
same information is available in the 'iov' member.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Dataset Management is not subject to MDTS, but exceeded a certain size
per range causes internal looping. Report this limit (DMRSL) in the NVM
command set specific identify controller data structure.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a trace event for the offline zone condition when checking zone
read.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
assert may be compiled to a noop and we could end up returning an
uninitialized status.
Fix this by always returning Internal Device Error as a fallback.
Note that, as pointed out by Philippe, per commit 262a69f4282 ("osdep.h:
Prohibit disabling assert() in supported builds") this shouldn't be
possible. But clean it up so we don't worry about it again.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add a trace event for the Identify command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Remove an unnecessary le_to_cpu conversion in Identify.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
ZASL (Zone Append Size Limit) is defined exactly like MDTS (Maximum Data
Transfer Size), that is, it is a value in units of the minimum memory
page size (CAP.MPSMIN) and is reported as a power of two.
The 'mdts' nvme device parameter is specified as in the spec, but the
'zoned.append_size_limit' parameter is specified in bytes. This is
suboptimal for a number of reasons:
1. It is just plain confusing wrt. the definition of mdts.
2. There is a lot of complexity involved in validating the value; it
must be a power of two, it should be larger than 4k, if it is zero
we set it internally to mdts, but still report it as zero.
3. While "hw/block/nvme: improve invalid zasl value reporting"
slightly improved the handling of the parameter, the validation is
still wrong; it does not depend on CC.MPS, it depends on
CAP.MPSMIN. And we are not even checking that it is actually less
than or equal to MDTS, which is kinda the *one* condition it must
satisfy.
Fix this by defining zasl exactly like mdts and checking the one thing
that it must satisfy (that it is less than or equal to mdts). Also,
change the default value from 128KiB to 0 (aka, whatever mdts is).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 6eb7a071292a ("hw/block/nvme: change controller pci id") changed
the controller to use a Red Hat assigned PCI Device and Vendor ID, but
did not change the IEEE OUI away from the Intel IEEE OUI.
Fix that and use the locally assigned QEMU IEEE OUI instead if the
`use-intel-id` parameter is not explicitly set. Also reverse the Intel
IEEE OUI bytes.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Zone Append Size Limit (ZASL) must be at least 4096 bytes, so
improve the user experience by adding an early parameter check in
nvme_check_constraints.
When ZASL is still too small due to the host configuring the device for
an even larger page size, convert the trace point in nvme_start_ctrl to
an NVME_GUEST_ERR such that this is logged by QEMU instead of only
traced.
Reported-by: Corne <info@dantalion.nl>
Cc: Dmitry Fomichev <Dmitry.Fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Firstly, if zoned.max_active is non-zero, zoned.max_open must be less
than or equal to zoned.max_active.
Secondly, if only zones.max_active is set, we have to explicitly set
zones.max_open or we end up with an invalid MAR/MOR configuration. This
is an artifact of the parameters not being zeroes-based like in the
spec.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reported-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and Explicitly Open zones can be closed by Close Zone
management function. This got broken by a recent commit ("hw/block/nvme:
refactor zone resource management") and now such commands fail with
Invalid Zone State Transition status.
Modify nvm_zrm_close() function to make Close Zone work correctly.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for TP 4065a ("Simple Copy Command"), v2020.05.04
("Ratified").
The implementation uses a bounce buffer to first read in the source
logical blocks, then issue a write of that bounce buffer. The default
maximum number of source logical blocks is 128, translating to 512 KiB
for 4k logical blocks which aligns with the default value of MDTS.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
In preparation for Simple Copy, pull write pointer advancement into a
separate function that is independent off an NvmeRequest.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Zone transition handling and resource management is open coded (and
semi-duplicated in the case of open, close and finish).
In preparation for Simple Copy command support (which also needs to open
zones for writing), consolidate into a set of 'nvme_zrm' functions and
in the process fix a bug with the controller not closing an open zone to
allow another zone to be explicitly opened.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Remove the unused NvmeCtrl parameter in nvme_check_zone_write.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
nvme-ns device is registered to a nvme controller device during the
initialization in nvme_register_namespace() in case that 'bus' property
is given which means it's mapped to a single controller.
This patch introduced a new property 'subsys' just like the controller
device instance did to map a namespace to a NVMe subsystem.
If 'subsys' property is given to the nvme-ns device, it will belong to
the specified subsystem and will be attached to all controllers in that
subsystem by enabling shared namespace capability in NMIC(Namespace
Multi-path I/O and Namespace Capabilities) in Identify Namespace.
Usage:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme,serial=bar,id=nvme1,subsys=subsys0
-device nvme,serial=baz,id=nvme2,subsys=subsys0
-device nvme-ns,id=ns1,drive=<drv>,nsid=1,subsys=subsys0 # Shared
-device nvme-ns,id=ns2,drive=<drv>,nsid=2,bus=nvme2 # Non-shared
In the above example, 'ns1' will be shared to 'nvme0' and 'nvme1' in
the same subsystem. On the other hand, 'ns2' will be attached to the
'nvme2' only as a private namespace in that subsystem.
All the namespace with 'subsys' parameter will attach all controllers in
the subsystem to the namespace by default.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
We have nvme-subsys and nvme devices mapped together. To support
multi-controller scheme to this setup, controller identifier(id) has to
be managed. Earlier, cntlid(controller id) used to be always 0 because
we didn't have any subsystem scheme that controller id matters.
This patch introduced 'cntlid' attribute to the nvme controller
instance(NvmeCtrl) and make it allocated by the nvme-subsys device
mapped to the controller. If nvme-subsys is not given to the
controller, then it will always be 0 as it was.
Added 'ctrls' array in the nvme-subsys instance to manage attached
controllers to the subsystem with a limit(32). This patch didn't take
list for the controllers to make it seamless with nvme-ns device.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme controller(nvme) can be mapped to a NVMe subsystem(nvme-subsys).
This patch maps a controller to a subsystem by adding a parameter
'subsys' to the nvme device.
To map a controller to a subsystem, we need to put nvme-subsys first and
then maps the subsystem to the controller:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
If 'subsys' property is not given to the nvme controller, then subsystem
NQN will be created with serial (e.g., 'foo' in above example),
Otherwise, it will be based on subsys id (e.g., 'subsys0' in above
example).
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
To support multi-path in QEMU NVMe device model, We need to have NVMe
subsystem hierarchy to map controllers and namespaces to a NVMe
subsystem.
This patch introduced a simple nvme-subsys device model. The subsystem
will be prepared with subsystem NQN with <subsys_id> provided in
nvme-subsys device:
ex) -device nvme-subsys,id=subsys0: nqn.2019-08.org.qemu:subsys0
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: added 'nqn' device parameter per request]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ZynqMP QSPI supports SPI transfer using DMA mode, but currently this
is unimplemented. When QSPI is programmed to use DMA mode, QEMU will
crash. This is observed when testing VxWorks 7.
This adds a Xilinx CSU DMA model and the implementation is based on
https://github.com/Xilinx/qemu/blob/master/hw/dma/csu_stream_dma.c.
The DST part of the model is verified along with ZynqMP GQSPI model.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
Implement the minor changes required to the SCC block for AN547 images:
* CFG2 and CFG5 exist (like AN524)
* CFG3 is reserved (like AN524)
* CFG0 bit 1 is CPU_WAIT; we don't implement it, but note this
in the TODO comment
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-40-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
We've already broken migration compatibility for all the MPS
boards, so we might as well take advantage of this to simplify
the vmstate for the FPGAIO device by folding the counters
subsection into the main vmstate description.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-38-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
