tresor.bessoh
/
linuxdebug
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
linuxdebug/drivers/media/pci/tw5864/tw5864-reg.h

2133 lines
64 KiB
C
Raw Normal View History

null pointer error
2024-07-16 15:50:57 +02:00
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* TW5864 driver - registers description
*
* Copyright (C) 2016 Bluecherry, LLC <maintainers@bluecherrydvr.com>
*/
/* According to TW5864_datasheet_0.6d.pdf, tw5864b1-ds.pdf */
/* Register Description - Direct Map Space */
/* 0x0000 ~ 0x1ffc - H264 Register Map */
/* [15:0] The Version register for H264 core (Read Only) */
#define TW5864_H264REV 0x0000
#define TW5864_EMU 0x0004
/* Define controls in register TW5864_EMU */
/* DDR controller enabled */
#define TW5864_EMU_EN_DDR BIT(0)
/* Enable bit for Inter module */
#define TW5864_EMU_EN_ME BIT(1)
/* Enable bit for Sensor Interface module */
#define TW5864_EMU_EN_SEN BIT(2)
/* Enable bit for Host Burst Access */
#define TW5864_EMU_EN_BHOST BIT(3)
/* Enable bit for Loop Filter module */
#define TW5864_EMU_EN_LPF BIT(4)
/* Enable bit for PLBK module */
#define TW5864_EMU_EN_PLBK BIT(5)
/*
* Video Frame mapping in DDR
* 00 CIF
* 01 D1
* 10 Reserved
* 11 Reserved
*
*/
#define TW5864_DSP_FRAME_TYPE (3 << 6)
#define TW5864_DSP_FRAME_TYPE_D1 BIT(6)
#define TW5864_UNDECLARED_H264REV_PART2 0x0008
#define TW5864_SLICE 0x000c
/* Define controls in register TW5864_SLICE */
/* VLC Slice end flag */
#define TW5864_VLC_SLICE_END BIT(0)
/* Master Slice End Flag */
#define TW5864_MAS_SLICE_END BIT(4)
/* Host to start a new slice Address */
#define TW5864_START_NSLICE BIT(15)
/*
* [15:0] Two bit for each channel (channel 0 ~ 7). Each two bits are the buffer
* pointer for the last encoded frame of the corresponding channel.
*/
#define TW5864_ENC_BUF_PTR_REC1 0x0010
/* [5:0] DSP_MB_QP and [15:10] DSP_LPF_OFFSET */
#define TW5864_DSP_QP 0x0018
/* Define controls in register TW5864_DSP_QP */
/* [5:0] H264 QP Value for codec */
#define TW5864_DSP_MB_QP 0x003f
/*
* [15:10] H264 LPF_OFFSET Address
* (Default 0)
*/
#define TW5864_DSP_LPF_OFFSET 0xfc00
#define TW5864_DSP_CODEC 0x001c
/* Define controls in register TW5864_DSP_CODEC */
/*
* 0: Encode (TW5864 Default)
* 1: Decode
*/
#define TW5864_DSP_CODEC_MODE BIT(0)
/*
* 0->3 4 VLC data buffer in DDR (1M each)
* 0->7 8 VLC data buffer in DDR (512k each)
*/
#define TW5864_VLC_BUF_ID (7 << 2)
/*
* 0 4CIF in 1 MB
* 1 1CIF in 1 MB
*/
#define TW5864_CIF_MAP_MD BIT(6)
/*
* 0 2 falf D1 in 1 MB
* 1 1 half D1 in 1 MB
*/
#define TW5864_HD1_MAP_MD BIT(7)
/* VLC Stream valid */
#define TW5864_VLC_VLD BIT(8)
/* MV Vector Valid */
#define TW5864_MV_VECT_VLD BIT(9)
/* MV Flag Valid */
#define TW5864_MV_FLAG_VLD BIT(10)
#define TW5864_DSP_SEN 0x0020
/* Define controls in register TW5864_DSP_SEN */
/* Org Buffer Base for Luma (default 0) */
#define TW5864_DSP_SEN_PIC_LU 0x000f
/* Org Buffer Base for Chroma (default 4) */
#define TW5864_DSP_SEN_PIC_CHM 0x00f0
/* Maximum Number of Buffers (default 4) */
#define TW5864_DSP_SEN_PIC_MAX 0x0700
/*
* Original Frame D1 or HD1 switch
* (Default 0)
*/
#define TW5864_DSP_SEN_HFULL 0x1000
#define TW5864_DSP_REF_PIC 0x0024
/* Define controls in register TW5864_DSP_REF_PIC */
/* Ref Buffer Base for Luma (default 0) */
#define TW5864_DSP_REF_PIC_LU 0x000f
/* Ref Buffer Base for Chroma (default 4) */
#define TW5864_DSP_REF_PIC_CHM 0x00f0
/* Maximum Number of Buffers (default 4) */
#define TW5864_DSP_REF_PIC_MAX 0x0700
/* [15:0] SEN_EN_CH[n] SENIF original frame capture enable for each channel */
#define TW5864_SEN_EN_CH 0x0028
#define TW5864_DSP 0x002c
/* Define controls in register TW5864_DSP */
/* The ID for channel selected for encoding operation */
#define TW5864_DSP_ENC_CHN 0x000f
/* See DSP_MB_DELAY below */
#define TW5864_DSP_MB_WAIT 0x0010
/*
* DSP Chroma Switch
* 0 DDRB
* 1 DDRA
*/
#define TW5864_DSP_CHROM_SW 0x0020
/* VLC Flow Control: 1 for enable */
#define TW5864_DSP_FLW_CNTL 0x0040
/*
* If DSP_MB_WAIT == 0, MB delay is DSP_MB_DELAY * 16
* If DSP_MB_DELAY == 1, MB delay is DSP_MB_DELAY * 128
*/
#define TW5864_DSP_MB_DELAY 0x0f00
#define TW5864_DDR 0x0030
/* Define controls in register TW5864_DDR */
/* DDR Single Access Page Number */
#define TW5864_DDR_PAGE_CNTL 0x00ff
/* DDR-DPR Burst Read Enable */
#define TW5864_DDR_BRST_EN BIT(13)
/*
* DDR A/B Select as HOST access
* 0 Select DDRA
* 1 Select DDRB
*/
#define TW5864_DDR_AB_SEL BIT(14)
/*
* DDR Access Mode Select
* 0 Single R/W Access (Host <-> DDR)
* 1 Burst R/W Access (Host <-> DPR)
*/
#define TW5864_DDR_MODE BIT(15)
/* The original frame capture pointer. Two bits for each channel */
/* SENIF_ORG_FRM_PTR [15:0] */
#define TW5864_SENIF_ORG_FRM_PTR1 0x0038
/* SENIF_ORG_FRM_PTR [31:16] */
#define TW5864_SENIF_ORG_FRM_PTR2 0x003c
#define TW5864_DSP_SEN_MODE 0x0040
/* Define controls in register TW5864_DSP_SEN_MODE */
#define TW5864_DSP_SEN_MODE_CH0 0x000f
#define TW5864_DSP_SEN_MODE_CH1 0x00f0
/*
* [15:0]: ENC_BUF_PTR_REC[31:16] Two bit for each channel (channel 8 ~ 15).
* Each two bits are the buffer pointer for the last encoded frame of a channel
*/
#define TW5864_ENC_BUF_PTR_REC2 0x004c
/* Current MV Flag Status Pointer for Channel n. (Read only) */
/*
* [1:0] CH0_MV_PTR, ..., [15:14] CH7_MV_PTR
*/
#define TW5864_CH_MV_PTR1 0x0060
/*
* [1:0] CH8_MV_PTR, ..., [15:14] CH15_MV_PTR
*/
#define TW5864_CH_MV_PTR2 0x0064
/*
* [15:0] Reset Current MV Flag Status Pointer for Channel n (one bit each)
*/
#define TW5864_RST_MV_PTR 0x0068
#define TW5864_INTERLACING 0x0200
/* Define controls in register TW5864_INTERLACING */
/*
* Inter_Mode Start. 2-nd bit? A guess. Missing in datasheet. Without this bit
* set, the output video is interlaced (stripy).
*/
#define TW5864_DSP_INTER_ST BIT(1)
/* Deinterlacer Enable */
#define TW5864_DI_EN BIT(2)
/*
* De-interlacer Mode
* 1 Shuffled frame
* 0 Normal Un-Shuffled Frame
*/
#define TW5864_DI_MD BIT(3)
/*
* Down scale original frame in X direction
* 11: Un-used
* 10: down-sample to 1/4
* 01: down-sample to 1/2
* 00: down-sample disabled
*/
#define TW5864_DSP_DWN_X (3 << 4)
/*
* Down scale original frame in Y direction
* 11: Un-used
* 10: down-sample to 1/4
* 01: down-sample to 1/2
* 00: down-sample disabled
*/
#define TW5864_DSP_DWN_Y (3 << 6)
/*
* 1 Dual Stream
* 0 Single Stream
*/
#define TW5864_DUAL_STR BIT(8)
#define TW5864_DSP_REF 0x0204
/* Define controls in register TW5864_DSP_REF */
/* Number of reference frame (Default 1 for TW5864B) */
#define TW5864_DSP_REF_FRM 0x000f
/* Window size */
#define TW5864_DSP_WIN_SIZE 0x02f0
#define TW5864_DSP_SKIP 0x0208
/* Define controls in register TW5864_DSP_SKIP */
/*
* Skip Offset Enable bit
* 0 DSP_SKIP_OFFSET value is not used (default 8)
* 1 DSP_SKIP_OFFSET value is used in HW
*/
#define TW5864_DSP_SKIP_OFEN 0x0080
/* Skip mode cost offset (default 8) */
#define TW5864_DSP_SKIP_OFFSET 0x007f
#define TW5864_MOTION_SEARCH_ETC 0x020c
/* Define controls in register TW5864_MOTION_SEARCH_ETC */
/* Enable quarter pel search mode */
#define TW5864_QPEL_EN BIT(0)
/* Enable half pel search mode */
#define TW5864_HPEL_EN BIT(1)
/* Enable motion search mode */
#define TW5864_ME_EN BIT(2)
/* Enable Intra mode */
#define TW5864_INTRA_EN BIT(3)
/* Enable Skip Mode */
#define TW5864_SKIP_EN BIT(4)
/* Search Option (Default 2"b01) */
#define TW5864_SRCH_OPT (3 << 5)
#define TW5864_DSP_ENC_REC 0x0210
/* Define controls in register TW5864_DSP_ENC_REC */
/* Reference Buffer Pointer for encoding */
#define TW5864_DSP_ENC_REF_PTR 0x0007
/* Reconstruct Buffer pointer */
#define TW5864_DSP_REC_BUF_PTR 0x7000
/* [15:0] Lambda Value for H264 */
#define TW5864_DSP_REF_MVP_LAMBDA 0x0214
#define TW5864_DSP_PIC_MAX_MB 0x0218
/* Define controls in register TW5864_DSP_PIC_MAX_MB */
/* The MB number in Y direction for a frame */
#define TW5864_DSP_PIC_MAX_MB_Y 0x007f
/* The MB number in X direction for a frame */
#define TW5864_DSP_PIC_MAX_MB_X 0x7f00
/* The original frame pointer for encoding */
#define TW5864_DSP_ENC_ORG_PTR_REG 0x021c
/* Mask to use with TW5864_DSP_ENC_ORG_PTR */
#define TW5864_DSP_ENC_ORG_PTR_MASK 0x7000
/* Number of bits to shift with TW5864_DSP_ENC_ORG_PTR */
#define TW5864_DSP_ENC_ORG_PTR_SHIFT 12
/* DDR base address of OSD rectangle attribute data */
#define TW5864_DSP_OSD_ATTRI_BASE 0x0220
/* OSD enable bit for each channel */
#define TW5864_DSP_OSD_ENABLE 0x0228
/* 0x0280 ~ 0x029c - Motion Vector for 1st 4x4 Block, e.g., 80 (X), 84 (Y) */
#define TW5864_ME_MV_VEC1 0x0280
/* 0x02a0 ~ 0x02bc - Motion Vector for 2nd 4x4 Block, e.g., A0 (X), A4 (Y) */
#define TW5864_ME_MV_VEC2 0x02a0
/* 0x02c0 ~ 0x02dc - Motion Vector for 3rd 4x4 Block, e.g., C0 (X), C4 (Y) */
#define TW5864_ME_MV_VEC3 0x02c0
/* 0x02e0 ~ 0x02fc - Motion Vector for 4th 4x4 Block, e.g., E0 (X), E4 (Y) */
#define TW5864_ME_MV_VEC4 0x02e0
/*
* [5:0]
* if (intra16x16_cost < (intra4x4_cost+dsp_i4x4_offset))
* Intra_mode = intra16x16_mode
* Else
* Intra_mode = intra4x4_mode
*/
#define TW5864_DSP_I4x4_OFFSET 0x040c
/*
* [6:4]
* 0x5 Only 4x4
* 0x6 Only 16x16
* 0x7 16x16 & 4x4
*/
#define TW5864_DSP_INTRA_MODE 0x0410
#define TW5864_DSP_INTRA_MODE_SHIFT 4
#define TW5864_DSP_INTRA_MODE_MASK (7 << 4)
#define TW5864_DSP_INTRA_MODE_4x4 0x5
#define TW5864_DSP_INTRA_MODE_16x16 0x6
#define TW5864_DSP_INTRA_MODE_4x4_AND_16x16 0x7
/*
* [5:0] WEIGHT Factor for I4x4 cost calculation (QP dependent)
*/
#define TW5864_DSP_I4x4_WEIGHT 0x0414
/*
* [7:0] Offset used to affect Intra/ME model decision
* If (me_cost < intra_cost + dsp_resid_mode_offset)
* Pred_Mode = me_mode
* Else
* Pred_mode = intra_mode
*/
#define TW5864_DSP_RESID_MODE_OFFSET 0x0604
/* 0x0800 ~ 0x09ff - Quantization TABLE Values */
#define TW5864_QUAN_TAB 0x0800
/* Valid channel value [0; f], frame value [0; 3] */
#define TW5864_RT_CNTR_CH_FRM(channel, frame) \
(0x0c00 | (channel << 4) | (frame << 2))
#define TW5864_FRAME_BUS1 0x0d00
/*
* 1 Progressive in part A in bus n
* 0 Interlaced in part A in bus n
*/
#define TW5864_PROG_A BIT(0)
/*
* 1 Progressive in part B in bus n
* 0 Interlaced in part B in bus n
*/
#define TW5864_PROG_B BIT(1)
/*
* 1 Frame Mode in bus n
* 0 Field Mode in bus n
*/
#define TW5864_FRAME BIT(2)
/*
* 0 4CIF in bus n
* 1 1D1 + 4 CIF in bus n
* 2 2D1 in bus n
*/
#define TW5864_BUS_D1 (3 << 3)
/* Bus 1 goes in TW5864_FRAME_BUS1 in [4:0] */
/* Bus 2 goes in TW5864_FRAME_BUS1 in [12:8] */
#define TW5864_FRAME_BUS2 0x0d04
/* Bus 3 goes in TW5864_FRAME_BUS2 in [4:0] */
/* Bus 4 goes in TW5864_FRAME_BUS2 in [12:8] */
/* [15:0] Horizontal Mirror for channel n */
#define TW5864_SENIF_HOR_MIR 0x0d08
/* [15:0] Vertical Mirror for channel n */
#define TW5864_SENIF_VER_MIR 0x0d0c
/*
* FRAME_WIDTH_BUSn_A
* 0x15f: 4 CIF
* 0x2cf: 1 D1 + 3 CIF
* 0x2cf: 2 D1
* FRAME_WIDTH_BUSn_B
* 0x15f: 4 CIF
* 0x2cf: 1 D1 + 3 CIF
* 0x2cf: 2 D1
* FRAME_HEIGHT_BUSn_A
* 0x11f: 4CIF (PAL)
* 0x23f: 1D1 + 3CIF (PAL)
* 0x23f: 2 D1 (PAL)
* 0x0ef: 4CIF (NTSC)
* 0x1df: 1D1 + 3CIF (NTSC)
* 0x1df: 2 D1 (NTSC)
* FRAME_HEIGHT_BUSn_B
* 0x11f: 4CIF (PAL)
* 0x23f: 1D1 + 3CIF (PAL)
* 0x23f: 2 D1 (PAL)
* 0x0ef: 4CIF (NTSC)
* 0x1df: 1D1 + 3CIF (NTSC)
* 0x1df: 2 D1 (NTSC)
*/
#define TW5864_FRAME_WIDTH_BUS_A(bus) (0x0d10 + 0x0010 * bus)
#define TW5864_FRAME_WIDTH_BUS_B(bus) (0x0d14 + 0x0010 * bus)
#define TW5864_FRAME_HEIGHT_BUS_A(bus) (0x0d18 + 0x0010 * bus)
#define TW5864_FRAME_HEIGHT_BUS_B(bus) (0x0d1c + 0x0010 * bus)
/*
* 1: the bus mapped Channel n Full D1
* 0: the bus mapped Channel n Half D1
*/
#define TW5864_FULL_HALF_FLAG 0x0d50
/*
* 0 The bus mapped Channel select partA Mode
* 1 The bus mapped Channel select partB Mode
*/
#define TW5864_FULL_HALF_MODE_SEL 0x0d54
#define TW5864_VLC 0x1000
/* Define controls in register TW5864_VLC */
/* QP Value used by H264 CAVLC */
#define TW5864_VLC_SLICE_QP 0x003f
/*
* Swap byte order of VLC stream in d-word.
* 1 Normal (VLC output= [31:0])
* 0 Swap (VLC output={[23:16],[31:24],[7:0], [15:8]})
*/
#define TW5864_VLC_BYTE_SWP BIT(6)
/* Enable Adding 03 circuit for VLC stream */
#define TW5864_VLC_ADD03_EN BIT(7)
/* Number of bit for VLC bit Align */
#define TW5864_VLC_BIT_ALIGN_SHIFT 8
#define TW5864_VLC_BIT_ALIGN_MASK (0x1f << 8)
/*
* Synchronous Interface select for VLC Stream
* 1 CDC_VLCS_MAS read VLC stream
* 0 CPU read VLC stream
*/
#define TW5864_VLC_INF_SEL BIT(13)
/* Enable VLC overflow control */
#define TW5864_VLC_OVFL_CNTL BIT(14)
/*
* 1 PCI Master Mode
* 0 Non PCI Master Mode
*/
#define TW5864_VLC_PCI_SEL BIT(15)
/*
* 0 Enable Adding 03 to VLC header and stream
* 1 Disable Adding 03 to VLC header of "00000001"
*/
#define TW5864_VLC_A03_DISAB BIT(16)
/*
* Status of VLC stream in DDR (one bit for each buffer)
* 1 VLC is ready in buffer n (HW set)
* 0 VLC is not ready in buffer n (SW clear)
*/
#define TW5864_VLC_BUF_RDY_SHIFT 24
#define TW5864_VLC_BUF_RDY_MASK (0xff << 24)
/* Total number of bit in the slice */
#define TW5864_SLICE_TOTAL_BIT 0x1004
/* Total number of bit in the residue */
#define TW5864_RES_TOTAL_BIT 0x1008
#define TW5864_VLC_BUF 0x100c
/* Define controls in register TW5864_VLC_BUF */
/* VLC BK0 full status, write '1' to clear */
#define TW5864_VLC_BK0_FULL BIT(0)
/* VLC BK1 full status, write '1' to clear */
#define TW5864_VLC_BK1_FULL BIT(1)
/* VLC end slice status, write '1' to clear */
#define TW5864_VLC_END_SLICE BIT(2)
/* VLC Buffer overflow status, write '1' to clear */
#define TW5864_DSP_RD_OF BIT(3)
/* VLC string length in either buffer 0 or 1 at end of frame */
#define TW5864_VLC_STREAM_LEN_SHIFT 4
#define TW5864_VLC_STREAM_LEN_MASK (0x1ff << 4)
/* [15:0] Total coefficient number in a frame */
#define TW5864_TOTAL_COEF_NO 0x1010
/* [0] VLC Encoder Interrupt. Write '1' to clear */
#define TW5864_VLC_DSP_INTR 0x1014
/* [31:0] VLC stream CRC checksum */
#define TW5864_VLC_STREAM_CRC 0x1018
#define TW5864_VLC_RD 0x101c
/* Define controls in register TW5864_VLC_RD */
/*
* 1 Read VLC lookup Memory
* 0 Read VLC Stream Memory
*/
#define TW5864_VLC_RD_MEM BIT(0)
/*
* 1 Read VLC Stream Memory in burst mode
* 0 Read VLC Stream Memory in single mode
*/
#define TW5864_VLC_RD_BRST BIT(1)
/* 0x2000 ~ 0x2ffc - H264 Stream Memory Map */
/*
* A word is 4 bytes. I.e.,
* VLC_STREAM_MEM[0] address: 0x2000
* VLC_STREAM_MEM[1] address: 0x2004
* ...
* VLC_STREAM_MEM[3FF] address: 0x2ffc
*/
#define TW5864_VLC_STREAM_MEM_START 0x2000
#define TW5864_VLC_STREAM_MEM_MAX_OFFSET 0x3ff
#define TW5864_VLC_STREAM_MEM(offset) (TW5864_VLC_STREAM_MEM_START + 4 * offset)
/* 0x4000 ~ 0x4ffc - Audio Register Map */
/* [31:0] config 1ms cnt = Realtime clk/1000 */
#define TW5864_CFG_1MS_CNT 0x4000
#define TW5864_ADPCM 0x4004
/* Define controls in register TW5864_ADPCM */
/* ADPCM decoder enable */
#define TW5864_ADPCM_DEC BIT(0)
/* ADPCM input data enable */
#define TW5864_ADPCM_IN_DATA BIT(1)
/* ADPCM encoder enable */
#define TW5864_ADPCM_ENC BIT(2)
#define TW5864_AUD 0x4008
/* Define controls in register TW5864_AUD */
/* Record path PCM Audio enable bit for each channel */
#define TW5864_AUD_ORG_CH_EN 0x00ff
/* Speaker path PCM Audio Enable */
#define TW5864_SPK_ORG_EN BIT(16)
/*
* 0 16bit
* 1 8bit
*/
#define TW5864_AD_BIT_MODE BIT(17)
#define TW5864_AUD_TYPE_SHIFT 18
/*
* 0 PCM
* 3 ADPCM
*/
#define TW5864_AUD_TYPE (0xf << 18)
#define TW5864_AUD_SAMPLE_RATE_SHIFT 22
/*
* 0 8K
* 1 16K
*/
#define TW5864_AUD_SAMPLE_RATE (3 << 22)
/* Channel ID used to select audio channel (0 to 16) for loopback */
#define TW5864_TESTLOOP_CHID_SHIFT 24
#define TW5864_TESTLOOP_CHID (0x1f << 24)
/* Enable AD Loopback Test */
#define TW5864_TEST_ADLOOP_EN BIT(30)
/*
* 0 Asynchronous Mode or PCI target mode
* 1 PCI Initiator Mode
*/
#define TW5864_AUD_MODE BIT(31)
#define TW5864_AUD_ADPCM 0x400c
/* Define controls in register TW5864_AUD_ADPCM */
/* Record path ADPCM audio channel enable, one bit for each */
#define TW5864_AUD_ADPCM_CH_EN 0x00ff
/* Speaker path ADPCM audio channel enable */
#define TW5864_SPK_ADPCM_EN BIT(16)
#define TW5864_PC_BLOCK_ADPCM_RD_NO 0x4018
#define TW5864_PC_BLOCK_ADPCM_RD_NO_MASK 0x1f
/*
* For ADPCM_ENC_WR_PTR, ADPCM_ENC_RD_PTR (see below):
* Bit[2:0] ch0
* Bit[5:3] ch1
* Bit[8:6] ch2
* Bit[11:9] ch3
* Bit[14:12] ch4
* Bit[17:15] ch5
* Bit[20:18] ch6
* Bit[23:21] ch7
* Bit[26:24] ch8
* Bit[29:27] ch9
* Bit[32:30] ch10
* Bit[35:33] ch11
* Bit[38:36] ch12
* Bit[41:39] ch13
* Bit[44:42] ch14
* Bit[47:45] ch15
* Bit[50:48] ch16
*/
#define TW5864_ADPCM_ENC_XX_MASK 0x3fff
#define TW5864_ADPCM_ENC_XX_PTR2_SHIFT 30
/* ADPCM_ENC_WR_PTR[29:0] */
#define TW5864_ADPCM_ENC_WR_PTR1 0x401c
/* ADPCM_ENC_WR_PTR[50:30] */
#define TW5864_ADPCM_ENC_WR_PTR2 0x4020
/* ADPCM_ENC_RD_PTR[29:0] */
#define TW5864_ADPCM_ENC_RD_PTR1 0x4024
/* ADPCM_ENC_RD_PTR[50:30] */
#define TW5864_ADPCM_ENC_RD_PTR2 0x4028
/* [3:0] rd ch0, [7:4] rd ch1, [11:8] wr ch0, [15:12] wr ch1 */
#define TW5864_ADPCM_DEC_RD_WR_PTR 0x402c
/*
* For TW5864_AD_ORIG_WR_PTR, TW5864_AD_ORIG_RD_PTR:
* Bit[3:0] ch0
* Bit[7:4] ch1
* Bit[11:8] ch2
* Bit[15:12] ch3
* Bit[19:16] ch4
* Bit[23:20] ch5
* Bit[27:24] ch6
* Bit[31:28] ch7
* Bit[35:32] ch8
* Bit[39:36] ch9
* Bit[43:40] ch10
* Bit[47:44] ch11
* Bit[51:48] ch12
* Bit[55:52] ch13
* Bit[59:56] ch14
* Bit[63:60] ch15
* Bit[67:64] ch16
*/
/* AD_ORIG_WR_PTR[31:0] */
#define TW5864_AD_ORIG_WR_PTR1 0x4030
/* AD_ORIG_WR_PTR[63:32] */
#define TW5864_AD_ORIG_WR_PTR2 0x4034
/* AD_ORIG_WR_PTR[67:64] */
#define TW5864_AD_ORIG_WR_PTR3 0x4038
/* AD_ORIG_RD_PTR[31:0] */
#define TW5864_AD_ORIG_RD_PTR1 0x403c
/* AD_ORIG_RD_PTR[63:32] */
#define TW5864_AD_ORIG_RD_PTR2 0x4040
/* AD_ORIG_RD_PTR[67:64] */
#define TW5864_AD_ORIG_RD_PTR3 0x4044
#define TW5864_PC_BLOCK_ORIG_RD_NO 0x4048
#define TW5864_PC_BLOCK_ORIG_RD_NO_MASK 0x1f
#define TW5864_PCI_AUD 0x404c
/* Define controls in register TW5864_PCI_AUD */
/*
* The register is applicable to PCI initiator mode only. Used to select PCM(0)
* or ADPCM(1) audio data sent to PC. One bit for each channel
*/
#define TW5864_PCI_DATA_SEL 0xffff
/*
* Audio flow control mode selection bit.
* 0 Flow control disabled. TW5864 continuously sends audio frame to PC
* (initiator mode)
* 1 Flow control enabled
*/
#define TW5864_PCI_FLOW_EN BIT(16)
/*
* When PCI_FLOW_EN is set, PCI need to toggle this bit to send an audio frame
* to PC. One toggle to send one frame.
*/
#define TW5864_PCI_AUD_FRM_EN BIT(17)
/* [1:0] CS valid to data valid CLK cycles when writing operation */
#define TW5864_CS2DAT_CNT 0x8000
/* [2:0] Data valid signal width by system clock cycles */
#define TW5864_DATA_VLD_WIDTH 0x8004
#define TW5864_SYNC 0x8008
/* Define controls in register TW5864_SYNC */
/*
* 0 vlc stream to synchronous port
* 1 vlc stream to ddr buffers
*/
#define TW5864_SYNC_CFG BIT(7)
/*
* 0 SYNC Address sampled on Rising edge
* 1 SYNC Address sampled on Falling edge
*/
#define TW5864_SYNC_ADR_EDGE BIT(0)
#define TW5864_VLC_STR_DELAY_SHIFT 1
/*
* 0 No system delay
* 1 One system clock delay
* 2 Two system clock delay
* 3 Three system clock delay
*/
#define TW5864_VLC_STR_DELAY (3 << 1)
/*
* 0 Rising edge output
* 1 Falling edge output
*/
#define TW5864_VLC_OUT_EDGE BIT(3)
/*
* [1:0]
* 2'b00 phase set to 180 degree
* 2'b01 phase set to 270 degree
* 2'b10 phase set to 0 degree
* 2'b11 phase set to 90 degree
*/
#define TW5864_I2C_PHASE_CFG 0x800c
/*
* The system / DDR clock (166 MHz) is generated with an on-chip system clock
* PLL (SYSPLL) using input crystal clock of 27 MHz. The system clock PLL
* frequency is controlled with the following equation.
* CLK_OUT = CLK_IN * (M+1) / ((N+1) * P)
* SYSPLL_M M parameter
* SYSPLL_N N parameter
* SYSPLL_P P parameter
*/
/* SYSPLL_M[7:0] */
#define TW5864_SYSPLL1 0x8018
/* Define controls in register TW5864_SYSPLL1 */
#define TW5864_SYSPLL_M_LOW 0x00ff
/* [2:0]: SYSPLL_M[10:8], [7:3]: SYSPLL_N[4:0] */
#define TW5864_SYSPLL2 0x8019
/* Define controls in register TW5864_SYSPLL2 */
#define TW5864_SYSPLL_M_HI 0x07
#define TW5864_SYSPLL_N_LOW_SHIFT 3
#define TW5864_SYSPLL_N_LOW (0x1f << 3)
/*
* [1:0]: SYSPLL_N[6:5], [3:2]: SYSPLL_P, [4]: SYSPLL_IREF, [7:5]: SYSPLL_CP_SEL
*/
#define TW5864_SYSPLL3 0x8020
/* Define controls in register TW5864_SYSPLL3 */
#define TW5864_SYSPLL_N_HI 0x03
#define TW5864_SYSPLL_P_SHIFT 2
#define TW5864_SYSPLL_P (0x03 << 2)
/*
* SYSPLL bias current control
* 0 Lower current (default)
* 1 30% higher current
*/
#define TW5864_SYSPLL_IREF BIT(4)
/*
* SYSPLL charge pump current selection
* 0 1,5 uA
* 1 4 uA
* 2 9 uA
* 3 19 uA
* 4 39 uA
* 5 79 uA
* 6 159 uA
* 7 319 uA
*/
#define TW5864_SYSPLL_CP_SEL_SHIFT 5
#define TW5864_SYSPLL_CP_SEL (0x07 << 5)
/*
* [1:0]: SYSPLL_VCO, [3:2]: SYSPLL_LP_X8, [5:4]: SYSPLL_ICP_SEL,
* [6]: SYSPLL_LPF_5PF, [7]: SYSPLL_ED_SEL
*/
#define TW5864_SYSPLL4 0x8021
/* Define controls in register TW5864_SYSPLL4 */
/*
* SYSPLL_VCO VCO Range selection
* 00 5 ~ 75 MHz
* 01 50 ~ 140 MHz
* 10 110 ~ 320 MHz
* 11 270 ~ 700 MHz
*/
#define TW5864_SYSPLL_VCO 0x03
#define TW5864_SYSPLL_LP_X8_SHIFT 2
/*
* Loop resister
* 0 38.5K ohms
* 1 6.6K ohms (default)
* 2 2.2K ohms
* 3 1.1K ohms
*/
#define TW5864_SYSPLL_LP_X8 (0x03 << 2)
#define TW5864_SYSPLL_ICP_SEL_SHIFT 4
/*
* PLL charge pump fine tune
* 00 x1 (default)
* 01 x1/2
* 10 x1/7
* 11 x1/8
*/
#define TW5864_SYSPLL_ICP_SEL (0x03 << 4)
/*
* PLL low pass filter phase margin adjustment
* 0 no 5pF (default)
* 1 5pF added
*/
#define TW5864_SYSPLL_LPF_5PF BIT(6)
/*
* PFD select edge for detection
* 0 Falling edge (default)
* 1 Rising edge
*/
#define TW5864_SYSPLL_ED_SEL BIT(7)
/* [0]: SYSPLL_RST, [4]: SYSPLL_PD */
#define TW5864_SYSPLL5 0x8024
/* Define controls in register TW5864_SYSPLL5 */
/* Reset SYSPLL */
#define TW5864_SYSPLL_RST BIT(0)
/* Power down SYSPLL */
#define TW5864_SYSPLL_PD BIT(4)
#define TW5864_PLL_CFG 0x801c
/* Define controls in register TW5864_PLL_CFG */
/*
* Issue Soft Reset from Async Host Interface / PCI Interface clock domain.
* Become valid after sync to the xtal clock domain. This bit is set only if
* LOAD register bit is also set to 1.
*/
#define TW5864_SRST BIT(0)
/*
* Issue SYSPLL (166 MHz) configuration latch from Async host interface / PCI
* Interface clock domain. The configuration setting becomes effective only if
* LOAD register bit is also set to 1.
*/
#define TW5864_SYSPLL_CFG BIT(2)
/*
* Issue SPLL (108 MHz) configuration load from Async host interface / PCI
* Interface clock domain. The configuration setting becomes effective only if
* the LOAD register bit is also set to 1.
*/
#define TW5864_SPLL_CFG BIT(4)
/*
* Set this bit to latch the SRST, SYSPLL_CFG, SPLL_CFG setting into the xtal
* clock domain to restart the PLL. This bit is self cleared.
*/
#define TW5864_LOAD BIT(3)
/* SPLL_IREF, SPLL_LPX4, SPLL_CPX4, SPLL_PD, SPLL_DBG */
#define TW5864_SPLL 0x8028
/* 0x8800 ~ 0x88fc - Interrupt Register Map */
/*
* Trigger mode of interrupt source 0 ~ 15
* 1 Edge trigger mode
* 0 Level trigger mode
*/
#define TW5864_TRIGGER_MODE_L 0x8800
/* Trigger mode of interrupt source 16 ~ 31 */
#define TW5864_TRIGGER_MODE_H 0x8804
/* Enable of interrupt source 0 ~ 15 */
#define TW5864_INTR_ENABLE_L 0x8808
/* Enable of interrupt source 16 ~ 31 */
#define TW5864_INTR_ENABLE_H 0x880c
/* Clear interrupt command of interrupt source 0 ~ 15 */
#define TW5864_INTR_CLR_L 0x8810
/* Clear interrupt command of interrupt source 16 ~ 31 */
#define TW5864_INTR_CLR_H 0x8814
/*
* Assertion of interrupt source 0 ~ 15
* 1 High level or pos-edge is assertion
* 0 Low level or neg-edge is assertion
*/
#define TW5864_INTR_ASSERT_L 0x8818
/* Assertion of interrupt source 16 ~ 31 */
#define TW5864_INTR_ASSERT_H 0x881c
/*
* Output level of interrupt
* 1 Interrupt output is high assertion
* 0 Interrupt output is low assertion
*/
#define TW5864_INTR_OUT_LEVEL 0x8820
/*
* Status of interrupt source 0 ~ 15
* Bit[0]: VLC 4k RAM interrupt
* Bit[1]: BURST DDR RAM interrupt
* Bit[2]: MV DSP interrupt
* Bit[3]: video lost interrupt
* Bit[4]: gpio 0 interrupt
* Bit[5]: gpio 1 interrupt
* Bit[6]: gpio 2 interrupt
* Bit[7]: gpio 3 interrupt
* Bit[8]: gpio 4 interrupt
* Bit[9]: gpio 5 interrupt
* Bit[10]: gpio 6 interrupt
* Bit[11]: gpio 7 interrupt
* Bit[12]: JPEG interrupt
* Bit[13:15]: Reserved
*/
#define TW5864_INTR_STATUS_L 0x8838
/*
* Status of interrupt source 16 ~ 31
* Bit[0]: Reserved
* Bit[1]: VLC done interrupt
* Bit[2]: Reserved
* Bit[3]: AD Vsync interrupt
* Bit[4]: Preview eof interrupt
* Bit[5]: Preview overflow interrupt
* Bit[6]: Timer interrupt
* Bit[7]: Reserved
* Bit[8]: Audio eof interrupt
* Bit[9]: I2C done interrupt
* Bit[10]: AD interrupt
* Bit[11:15]: Reserved
*/
#define TW5864_INTR_STATUS_H 0x883c
/* Defines of interrupt bits, united for both low and high word registers */
#define TW5864_INTR_VLC_RAM BIT(0)
#define TW5864_INTR_BURST BIT(1)
#define TW5864_INTR_MV_DSP BIT(2)
#define TW5864_INTR_VIN_LOST BIT(3)
/* n belongs to [0; 7] */
#define TW5864_INTR_GPIO(n) (1 << (4 + n))
#define TW5864_INTR_JPEG BIT(12)
#define TW5864_INTR_VLC_DONE BIT(17)
#define TW5864_INTR_AD_VSYNC BIT(19)
#define TW5864_INTR_PV_EOF BIT(20)
#define TW5864_INTR_PV_OVERFLOW BIT(21)
#define TW5864_INTR_TIMER BIT(22)
#define TW5864_INTR_AUD_EOF BIT(24)
#define TW5864_INTR_I2C_DONE BIT(25)
#define TW5864_INTR_AD BIT(26)
/* 0x9000 ~ 0x920c - Video Capture (VIF) Register Map */
/*
* H264EN_CH_STATUS[n] Status of Vsync synchronized H264EN_CH_EN (Read Only)
* 1 Channel Enabled
* 0 Channel Disabled
*/
#define TW5864_H264EN_CH_STATUS 0x9000
/*
* [15:0] H264EN_CH_EN[n] H264 Encoding Path Enable for channel
* 1 Channel Enabled
* 0 Channel Disabled
*/
#define TW5864_H264EN_CH_EN 0x9004
/*
* H264EN_CH_DNS[n] H264 Encoding Path Downscale Video Decoder Input for
* channel n
* 1 Downscale Y to 1/2
* 0 Does not downscale
*/
#define TW5864_H264EN_CH_DNS 0x9008
/*
* H264EN_CH_PROG[n] H264 Encoding Path channel n is progressive
* 1 Progressive (Not valid for TW5864)
* 0 Interlaced (TW5864 default)
*/
#define TW5864_H264EN_CH_PROG 0x900c
/*
* [3:0] H264EN_BUS_MAX_CH[n]
* H264 Encoding Path maximum number of channel on BUS n
* 0 Max 4 channels
* 1 Max 2 channels
*/
#define TW5864_H264EN_BUS_MAX_CH 0x9010
/*
* H264EN_RATE_MAX_LINE_n H264 Encoding path Rate Mapping Maximum Line Number
* on Bus n
*/
#define TW5864_H264EN_RATE_MAX_LINE_EVEN 0x1f
#define TW5864_H264EN_RATE_MAX_LINE_ODD_SHIFT 5
#define TW5864_H264EN_RATE_MAX_LINE_ODD (0x1f << 5)
/*
* [4:0] H264EN_RATE_MAX_LINE_0
* [9:5] H264EN_RATE_MAX_LINE_1
*/
#define TW5864_H264EN_RATE_MAX_LINE_REG1 0x9014
/*
* [4:0] H264EN_RATE_MAX_LINE_2
* [9:5] H264EN_RATE_MAX_LINE_3
*/
#define TW5864_H264EN_RATE_MAX_LINE_REG2 0x9018
/*
* H264EN_CHn_FMT H264 Encoding Path Format configuration of Channel n
* 00 D1 (For D1 and hD1 frame)
* 01 (Reserved)
* 10 (Reserved)
* 11 D1 with 1/2 size in X (for CIF frame)
* Note: To be used with 0x9008 register to configure the frame size
*/
/*
* [1:0]: H264EN_CH0_FMT,
* ..., [15:14]: H264EN_CH7_FMT
*/
#define TW5864_H264EN_CH_FMT_REG1 0x9020
/*
* [1:0]: H264EN_CH8_FMT (?),
* ..., [15:14]: H264EN_CH15_FMT (?)
*/
#define TW5864_H264EN_CH_FMT_REG2 0x9024
/*
* H264EN_RATE_CNTL_BUSm_CHn H264 Encoding Path BUS m Rate Control for Channel n
*/
#define TW5864_H264EN_RATE_CNTL_LO_WORD(bus, channel) \
(0x9100 + bus * 0x20 + channel * 0x08)
#define TW5864_H264EN_RATE_CNTL_HI_WORD(bus, channel) \
(0x9104 + bus * 0x20 + channel * 0x08)
/*
* H264EN_BUSm_MAP_CHn The 16-to-1 MUX configuration register for each encoding
* channel (total of 16 channels). Four bits for each channel.
*/
#define TW5864_H264EN_BUS0_MAP 0x9200
#define TW5864_H264EN_BUS1_MAP 0x9204
#define TW5864_H264EN_BUS2_MAP 0x9208
#define TW5864_H264EN_BUS3_MAP 0x920c
/* This register is not defined in datasheet, but used in reference driver */
#define TW5864_UNDECLARED_ERROR_FLAGS_0x9218 0x9218
#define TW5864_GPIO1 0x9800
#define TW5864_GPIO2 0x9804
/* Define controls in registers TW5864_GPIO1, TW5864_GPIO2 */
/* GPIO DATA of Group n */
#define TW5864_GPIO_DATA 0x00ff
#define TW5864_GPIO_OEN_SHIFT 8
/* GPIO Output Enable of Group n */
#define TW5864_GPIO_OEN (0xff << 8)
/* 0xa000 ~ 0xa8ff - DDR Controller Register Map */
/* DDR Controller A */
/*
* [2:0] Data valid counter after read command to DDR. This is the delay value
* to show how many cycles the data will be back from DDR after we issue a read
* command.
*/
#define TW5864_RD_ACK_VLD_MUX 0xa000
#define TW5864_DDR_PERIODS 0xa004
/* Define controls in register TW5864_DDR_PERIODS */
/*
* Tras value, the minimum cycle of active to precharge command period,
* default is 7
*/
#define TW5864_TRAS_CNT_MAX 0x000f
/*
* Trfc value, the minimum cycle of refresh to active or refresh command period,
* default is 4"hf
*/
#define TW5864_RFC_CNT_MAX_SHIFT 8
#define TW5864_RFC_CNT_MAX (0x0f << 8)
/*
* Trcd value, the minimum cycle of active to internal read/write command
* period, default is 4"h2
*/
#define TW5864_TCD_CNT_MAX_SHIFT 4
#define TW5864_TCD_CNT_MAX (0x0f << 4)
/* Twr value, write recovery time, default is 4"h3 */
#define TW5864_TWR_CNT_MAX_SHIFT 12
#define TW5864_TWR_CNT_MAX (0x0f << 12)
/*
* [2:0] CAS latency, the delay cycle between internal read command and the
* availability of the first bit of output data, default is 3
*/
#define TW5864_CAS_LATENCY 0xa008
/*
* [15:0] Maximum average periodic refresh, the value is based on the current
* frequency to match 7.8mcs
*/
#define TW5864_DDR_REF_CNTR_MAX 0xa00c
/*
* DDR_ON_CHIP_MAP [1:0]
* 0 256M DDR on board
* 1 512M DDR on board
* 2 1G DDR on board
* DDR_ON_CHIP_MAP [2]
* 0 Only one DDR chip
* 1 Two DDR chips
*/
#define TW5864_DDR_ON_CHIP_MAP 0xa01c
#define TW5864_DDR_SELFTEST_MODE 0xa020
/* Define controls in register TW5864_DDR_SELFTEST_MODE */
/*
* 0 Common read/write mode
* 1 DDR self-test mode
*/
#define TW5864_MASTER_MODE BIT(0)
/*
* 0 DDR self-test single read/write
* 1 DDR self-test burst read/write
*/
#define TW5864_SINGLE_PROC BIT(1)
/*
* 0 DDR self-test write command
* 1 DDR self-test read command
*/
#define TW5864_WRITE_FLAG BIT(2)
#define TW5864_DATA_MODE_SHIFT 4
/*
* 0 write 32'haaaa5555 to DDR
* 1 write 32'hffffffff to DDR
* 2 write 32'hha5a55a5a to DDR
* 3 write increasing data to DDR
*/
#define TW5864_DATA_MODE (0x3 << 4)
/* [7:0] The maximum data of one burst in DDR self-test mode */
#define TW5864_BURST_CNTR_MAX 0xa024
/* [15:0] The maximum burst counter (bit 15~0) in DDR self-test mode */
#define TW5864_DDR_PROC_CNTR_MAX_L 0xa028
/* The maximum burst counter (bit 31~16) in DDR self-test mode */
#define TW5864_DDR_PROC_CNTR_MAX_H 0xa02c
/* [0]: Start one DDR self-test */
#define TW5864_DDR_SELF_TEST_CMD 0xa030
/* The maximum error counter (bit 15 ~ 0) in DDR self-test */
#define TW5864_ERR_CNTR_L 0xa034
#define TW5864_ERR_CNTR_H_AND_FLAG 0xa038
/* Define controls in register TW5864_ERR_CNTR_H_AND_FLAG */
/* The maximum error counter (bit 30 ~ 16) in DDR self-test */
#define TW5864_ERR_CNTR_H_MASK 0x3fff
/* DDR self-test end flag */
#define TW5864_END_FLAG 0x8000
/*
* DDR Controller B: same as 0xa000 ~ 0xa038, but add TW5864_DDR_B_OFFSET to all
* addresses
*/
#define TW5864_DDR_B_OFFSET 0x0800
/* 0xb004 ~ 0xb018 - HW version/ARB12 Register Map */
/* [15:0] Default is C013 */
#define TW5864_HW_VERSION 0xb004
#define TW5864_REQS_ENABLE 0xb010
/* Define controls in register TW5864_REQS_ENABLE */
/* Audio data in to DDR enable (default 1) */
#define TW5864_AUD_DATA_IN_ENB BIT(0)
/* Audio encode request to DDR enable (default 1) */
#define TW5864_AUD_ENC_REQ_ENB BIT(1)
/* Audio decode request0 to DDR enable (default 1) */
#define TW5864_AUD_DEC_REQ0_ENB BIT(2)
/* Audio decode request1 to DDR enable (default 1) */
#define TW5864_AUD_DEC_REQ1_ENB BIT(3)
/* VLC stream request to DDR enable (default 1) */
#define TW5864_VLC_STRM_REQ_ENB BIT(4)
/* H264 MV request to DDR enable (default 1) */
#define TW5864_DVM_MV_REQ_ENB BIT(5)
/* mux_core MVD request to DDR enable (default 1) */
#define TW5864_MVD_REQ_ENB BIT(6)
/* mux_core MVD temp data request to DDR enable (default 1) */
#define TW5864_MVD_TMP_REQ_ENB BIT(7)
/* JPEG request to DDR enable (default 1) */
#define TW5864_JPEG_REQ_ENB BIT(8)
/* mv_flag request to DDR enable (default 1) */
#define TW5864_MV_FLAG_REQ_ENB BIT(9)
#define TW5864_ARB12 0xb018
/* Define controls in register TW5864_ARB12 */
/* ARB12 Enable (default 1) */
#define TW5864_ARB12_ENB BIT(15)
/* ARB12 maximum value of time out counter (default 15"h1FF) */
#define TW5864_ARB12_TIME_OUT_CNT 0x7fff
/* 0xb800 ~ 0xb80c - Indirect Access Register Map */
/*
* Spec says:
* In order to access the indirect register space, the following procedure is
* followed.
* But reference driver implementation, and current driver, too, does it
* differently.
*
* Write Registers:
* (1) Write IND_DATA at 0xb804 ~ 0xb807
* (2) Read BUSY flag from 0xb803. Wait until BUSY signal is 0.
* (3) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "1", ENABLE to "1"
* Read Registers:
* (1) Read BUSY flag from 0xb803. Wait until BUSY signal is 0.
* (2) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "0", ENABLE to "1"
* (3) Read BUSY flag from 0xb803. Wait until BUSY signal is 0.
* (4) Read IND_DATA from 0xb804 ~ 0xb807
*/
#define TW5864_IND_CTL 0xb800
/* Define controls in register TW5864_IND_CTL */
/* Address used to access indirect register space */
#define TW5864_IND_ADDR 0x0000ffff
/* Wait until this bit is "0" before using indirect access */
#define TW5864_BUSY BIT(31)
/* Activate the indirect access. This bit is self cleared */
#define TW5864_ENABLE BIT(25)
/* Read/Write command */
#define TW5864_RW BIT(24)
/* [31:0] Data used to read/write indirect register space */
#define TW5864_IND_DATA 0xb804
/* 0xc000 ~ 0xc7fc - Preview Register Map */
/* Mostly skipped this section. */
/*
* [15:0] Status of Vsync Synchronized PCI_PV_CH_EN (Read Only)
* 1 Channel Enabled
* 0 Channel Disabled
*/
#define TW5864_PCI_PV_CH_STATUS 0xc000
/*
* [15:0] PCI Preview Path Enable for channel n
* 1 Channel Enable
* 0 Channel Disable
*/
#define TW5864_PCI_PV_CH_EN 0xc004
/* 0xc800 ~ 0xc804 - JPEG Capture Register Map */
/* Skipped. */
/* 0xd000 ~ 0xd0fc - JPEG Control Register Map */
/* Skipped. */
/* 0xe000 ~ 0xfc04 - Motion Vector Register Map */
/* ME Motion Vector data (Four Byte Each) 0xe000 ~ 0xe7fc */
#define TW5864_ME_MV_VEC_START 0xe000
#define TW5864_ME_MV_VEC_MAX_OFFSET 0x1ff
#define TW5864_ME_MV_VEC(offset) (TW5864_ME_MV_VEC_START + 4 * offset)
#define TW5864_MV 0xfc00
/* Define controls in register TW5864_MV */
/* mv bank0 full status , write "1" to clear */
#define TW5864_MV_BK0_FULL BIT(0)
/* mv bank1 full status , write "1" to clear */
#define TW5864_MV_BK1_FULL BIT(1)
/* slice end status; write "1" to clear */
#define TW5864_MV_EOF BIT(2)
/* mv encode interrupt status; write "1" to clear */
#define TW5864_MV_DSP_INTR BIT(3)
/* mv write memory overflow, write "1" to clear */
#define TW5864_DSP_WR_OF BIT(4)
#define TW5864_MV_LEN_SHIFT 5
/* mv stream length */
#define TW5864_MV_LEN (0xff << 5)
/* The configured status bit written into bit 15 of 0xfc04 */
#define TW5864_MPI_DDR_SEL BIT(13)
#define TW5864_MPI_DDR_SEL_REG 0xfc04
/* Define controls in register TW5864_MPI_DDR_SEL_REG */
/*
* SW configure register
* 0 MV is saved in internal DPR
* 1 MV is saved in DDR
*/
#define TW5864_MPI_DDR_SEL2 BIT(15)
/* 0x18000 ~ 0x181fc - PCI Master/Slave Control Map */
#define TW5864_PCI_INTR_STATUS 0x18000
/* Define controls in register TW5864_PCI_INTR_STATUS */
/* vlc done */
#define TW5864_VLC_DONE_INTR BIT(1)
/* ad vsync */
#define TW5864_AD_VSYNC_INTR BIT(3)
/* preview eof */
#define TW5864_PREV_EOF_INTR BIT(4)
/* preview overflow interrupt */
#define TW5864_PREV_OVERFLOW_INTR BIT(5)
/* timer interrupt */
#define TW5864_TIMER_INTR BIT(6)
/* audio eof */
#define TW5864_AUDIO_EOF_INTR BIT(8)
/* IIC done */
#define TW5864_IIC_DONE_INTR BIT(24)
/* ad interrupt (e.g.: video lost, video format changed) */
#define TW5864_AD_INTR_REG BIT(25)
#define TW5864_PCI_INTR_CTL 0x18004
/* Define controls in register TW5864_PCI_INTR_CTL */
/* master enable */
#define TW5864_PCI_MAST_ENB BIT(0)
/* mvd&vlc master enable */
#define TW5864_MVD_VLC_MAST_ENB 0x06
/* (Need to set 0 in TW5864A) */
#define TW5864_AD_MAST_ENB BIT(3)
/* preview master enable */
#define TW5864_PREV_MAST_ENB BIT(4)
/* preview overflow enable */
#define TW5864_PREV_OVERFLOW_ENB BIT(5)
/* timer interrupt enable */
#define TW5864_TIMER_INTR_ENB BIT(6)
/* JPEG master (push mode) enable */
#define TW5864_JPEG_MAST_ENB BIT(7)
#define TW5864_AU_MAST_ENB_CHN_SHIFT 8
/* audio master channel enable */
#define TW5864_AU_MAST_ENB_CHN (0xffff << 8)
/* IIC interrupt enable */
#define TW5864_IIC_INTR_ENB BIT(24)
/* ad interrupt enable */
#define TW5864_AD_INTR_ENB BIT(25)
/* target burst enable */
#define TW5864_PCI_TAR_BURST_ENB BIT(26)
/* vlc stream burst enable */
#define TW5864_PCI_VLC_BURST_ENB BIT(27)
/* ddr burst enable (1 enable, and must set DDR_BRST_EN) */
#define TW5864_PCI_DDR_BURST_ENB BIT(28)
/*
* Because preview and audio have 16 channels separately, so using this
* registers to indicate interrupt status for every channels. This is secondary
* interrupt status register. OR operating of the PREV_INTR_REG is
* PREV_EOF_INTR, OR operating of the AU_INTR_REG bits is AUDIO_EOF_INTR
*/
#define TW5864_PREV_AND_AU_INTR 0x18008
/* Define controls in register TW5864_PREV_AND_AU_INTR */
/* preview eof interrupt flag */
#define TW5864_PREV_INTR_REG 0x0000ffff
#define TW5864_AU_INTR_REG_SHIFT 16
/* audio eof interrupt flag */
#define TW5864_AU_INTR_REG (0xffff << 16)
#define TW5864_MASTER_ENB_REG 0x1800c
/* Define controls in register TW5864_MASTER_ENB_REG */
/* master enable */
#define TW5864_PCI_VLC_INTR_ENB BIT(1)
/* mvd and vlc master enable */
#define TW5864_PCI_PREV_INTR_ENB BIT(4)
/* ad vsync master enable */
#define TW5864_PCI_PREV_OF_INTR_ENB BIT(5)
/* jpeg master enable */
#define TW5864_PCI_JPEG_INTR_ENB BIT(7)
/* preview master enable */
#define TW5864_PCI_AUD_INTR_ENB BIT(8)
/*
* Every channel of preview and audio have ping-pong buffers in system memory,
* this register is the buffer flag to notify software which buffer is been
* operated.
*/
#define TW5864_PREV_AND_AU_BUF_FLAG 0x18010
/* Define controls in register TW5864_PREV_AND_AU_BUF_FLAG */
/* preview buffer A/B flag */
#define TW5864_PREV_BUF_FLAG 0xffff
#define TW5864_AUDIO_BUF_FLAG_SHIFT 16
/* audio buffer A/B flag */
#define TW5864_AUDIO_BUF_FLAG (0xffff << 16)
#define TW5864_IIC 0x18014
/* Define controls in register TW5864_IIC */
/* register data */
#define TW5864_IIC_DATA 0x00ff
#define TW5864_IIC_REG_ADDR_SHIFT 8
/* register addr */
#define TW5864_IIC_REG_ADDR (0xff << 8)
/* rd/wr flag rd=1,wr=0 */
#define TW5864_IIC_RW BIT(16)
#define TW5864_IIC_DEV_ADDR_SHIFT 17
/* device addr */
#define TW5864_IIC_DEV_ADDR (0x7f << 17)
/*
* iic done, software kick off one time iic transaction through setting this
* bit to 1. Then poll this bit, value 1 indicate iic transaction have
* completed, if read, valid data have been stored in iic_data
*/
#define TW5864_IIC_DONE BIT(24)
#define TW5864_RST_AND_IF_INFO 0x18018
/* Define controls in register TW5864_RST_AND_IF_INFO */
/* application software soft reset */
#define TW5864_APP_SOFT_RST BIT(0)
#define TW5864_PCI_INF_VERSION_SHIFT 16
/* PCI interface version, read only */
#define TW5864_PCI_INF_VERSION (0xffff << 16)
/* vlc stream crc value, it is calculated in pci module */
#define TW5864_VLC_CRC_REG 0x1801c
/*
* vlc max length, it is defined by software based on software assign memory
* space for vlc
*/
#define TW5864_VLC_MAX_LENGTH 0x18020
/* vlc length of one frame */
#define TW5864_VLC_LENGTH 0x18024
/* vlc original crc value */
#define TW5864_VLC_INTRA_CRC_I_REG 0x18028
/* vlc original crc value */
#define TW5864_VLC_INTRA_CRC_O_REG 0x1802c
/* mv stream crc value, it is calculated in pci module */
#define TW5864_VLC_PAR_CRC_REG 0x18030
/* mv length */
#define TW5864_VLC_PAR_LENGTH_REG 0x18034
/* mv original crc value */
#define TW5864_VLC_PAR_I_REG 0x18038
/* mv original crc value */
#define TW5864_VLC_PAR_O_REG 0x1803c
/*
* Configuration register for 9[or 10] CIFs or 1D1+15QCIF Preview mode.
* PREV_PCI_ENB_CHN[0] Enable 9th preview channel (9CIF prev) or 1D1 channel in
* (1D1+15QCIF prev)
* PREV_PCI_ENB_CHN[1] Enable 10th preview channel
*/
#define TW5864_PREV_PCI_ENB_CHN 0x18040
/* Description skipped. */
#define TW5864_PREV_FRAME_FORMAT_IN 0x18044
/* IIC enable */
#define TW5864_IIC_ENB 0x18048
/*
* Timer interrupt interval
* 0 1ms
* 1 2ms
* 2 4ms
* 3 8ms
*/
#define TW5864_PCI_INTTM_SCALE 0x1804c
/*
* The above register is pci base address registers. Application software will
* initialize them to tell chip where the corresponding stream will be dumped
* to. Application software will select appropriate base address interval based
* on the stream length.
*/
/* VLC stream base address */
#define TW5864_VLC_STREAM_BASE_ADDR 0x18080
/* MV stream base address */
#define TW5864_MV_STREAM_BASE_ADDR 0x18084
/* 0x180a0 ~ 0x180bc: audio burst base address. Skipped. */
/* 0x180c0 ~ 0x180dc: JPEG Push Mode Buffer Base Address. Skipped. */
/* 0x18100 ~ 0x1817c: preview burst base address. Skipped. */
/* 0x80000 ~ 0x87fff - DDR Burst RW Register Map */
#define TW5864_DDR_CTL 0x80000
/* Define controls in register TW5864_DDR_CTL */
#define TW5864_BRST_LENGTH_SHIFT 2
/* Length of 32-bit data burst */
#define TW5864_BRST_LENGTH (0x3fff << 2)
/*
* Burst Read/Write
* 0 Read Burst from DDR
* 1 Write Burst to DDR
*/
#define TW5864_BRST_RW BIT(16)
/* Begin a new DDR Burst. This bit is self cleared */
#define TW5864_NEW_BRST_CMD BIT(17)
/* DDR Burst End Flag */
#define TW5864_BRST_END BIT(24)
/* Enable Error Interrupt for Single DDR Access */
#define TW5864_SING_ERR_INTR BIT(25)
/* Enable Error Interrupt for Burst DDR Access */
#define TW5864_BRST_ERR_INTR BIT(26)
/* Enable Interrupt for End of DDR Burst Access */
#define TW5864_BRST_END_INTR BIT(27)
/* DDR Single Access Error Flag */
#define TW5864_SINGLE_ERR BIT(28)
/* DDR Single Access Busy Flag */
#define TW5864_SINGLE_BUSY BIT(29)
/* DDR Burst Access Error Flag */
#define TW5864_BRST_ERR BIT(30)
/* DDR Burst Access Busy Flag */
#define TW5864_BRST_BUSY BIT(31)
/* [27:0] DDR Access Address. Bit [1:0] has to be 0 */
#define TW5864_DDR_ADDR 0x80004
/* DDR Access Internal Buffer Address. Bit [1:0] has to be 0 */
#define TW5864_DPR_BUF_ADDR 0x80008
/* SRAM Buffer MPI Access Space. Totally 16 KB */
#define TW5864_DPR_BUF_START 0x84000
/* 0x84000 - 0x87ffc */
#define TW5864_DPR_BUF_SIZE 0x4000
/* Indirect Map Space */
/*
* The indirect space is accessed through 0xb800 ~ 0xb807 registers in direct
* access space
*/
/* Analog Video / Audio Decoder / Encoder */
/* Allowed channel values: [0; 3] */
/* Read-only register */
#define TW5864_INDIR_VIN_0(channel) (0x000 + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_0 */
/*
* 1 Video not present. (sync is not detected in number of consecutive line
* periods specified by MISSCNT register)
* 0 Video detected.
*/
#define TW5864_INDIR_VIN_0_VDLOSS BIT(7)
/*
* 1 Horizontal sync PLL is locked to the incoming video source.
* 0 Horizontal sync PLL is not locked.
*/
#define TW5864_INDIR_VIN_0_HLOCK BIT(6)
/*
* 1 Sub-carrier PLL is locked to the incoming video source.
* 0 Sub-carrier PLL is not locked.
*/
#define TW5864_INDIR_VIN_0_SLOCK BIT(5)
/*
* 1 Even field is being decoded.
* 0 Odd field is being decoded.
*/
#define TW5864_INDIR_VIN_0_FLD BIT(4)
/*
* 1 Vertical logic is locked to the incoming video source.
* 0 Vertical logic is not locked.
*/
#define TW5864_INDIR_VIN_0_VLOCK BIT(3)
/*
* 1 No color burst signal detected.
* 0 Color burst signal detected.
*/
#define TW5864_INDIR_VIN_0_MONO BIT(1)
/*
* 0 60Hz source detected
* 1 50Hz source detected
* The actual vertical scanning frequency depends on the current standard
* invoked.
*/
#define TW5864_INDIR_VIN_0_DET50 BIT(0)
#define TW5864_INDIR_VIN_1(channel) (0x001 + channel * 0x010)
/* VCR signal indicator. Read-only. */
#define TW5864_INDIR_VIN_1_VCR BIT(7)
/* Weak signal indicator 2. Read-only. */
#define TW5864_INDIR_VIN_1_WKAIR BIT(6)
/* Weak signal indicator controlled by WKTH. Read-only. */
#define TW5864_INDIR_VIN_1_WKAIR1 BIT(5)
/*
* 1 = Standard signal
* 0 = Non-standard signal
* Read-only
*/
#define TW5864_INDIR_VIN_1_VSTD BIT(4)
/*
* 1 = Non-interlaced signal
* 0 = interlaced signal
* Read-only
*/
#define TW5864_INDIR_VIN_1_NINTL BIT(3)
/*
* Vertical Sharpness Control. Writable.
* 0 = None (default)
* 7 = Highest
* **Note: VSHP must be set to '0' if COMB = 0
*/
#define TW5864_INDIR_VIN_1_VSHP 0x07
/* HDELAY_XY[7:0] */
#define TW5864_INDIR_VIN_2_HDELAY_XY_LO(channel) (0x002 + channel * 0x010)
/* HACTIVE_XY[7:0] */
#define TW5864_INDIR_VIN_3_HACTIVE_XY_LO(channel) (0x003 + channel * 0x010)
/* VDELAY_XY[7:0] */
#define TW5864_INDIR_VIN_4_VDELAY_XY_LO(channel) (0x004 + channel * 0x010)
/* VACTIVE_XY[7:0] */
#define TW5864_INDIR_VIN_5_VACTIVE_XY_LO(channel) (0x005 + channel * 0x010)
#define TW5864_INDIR_VIN_6(channel) (0x006 + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_6 */
#define TW5864_INDIR_VIN_6_HDELAY_XY_HI 0x03
#define TW5864_INDIR_VIN_6_HACTIVE_XY_HI_SHIFT 2
#define TW5864_INDIR_VIN_6_HACTIVE_XY_HI (0x03 << 2)
#define TW5864_INDIR_VIN_6_VDELAY_XY_HI BIT(4)
#define TW5864_INDIR_VIN_6_VACTIVE_XY_HI BIT(5)
/*
* HDELAY_XY This 10bit register defines the starting location of horizontal
* active pixel for display / record path. A unit is 1 pixel. The default value
* is 0x00f for NTSC and 0x00a for PAL.
*
* HACTIVE_XY This 10bit register defines the number of horizontal active pixel
* for display / record path. A unit is 1 pixel. The default value is decimal
* 720.
*
* VDELAY_XY This 9bit register defines the starting location of vertical
* active for display / record path. A unit is 1 line. The default value is
* decimal 6.
*
* VACTIVE_XY This 9bit register defines the number of vertical active lines
* for display / record path. A unit is 1 line. The default value is decimal
* 240.
*/
/* HUE These bits control the color hue as 2's complement number. They have
* value from +36o (7Fh) to -36o (80h) with an increment of 2.8o. The 2 LSB has
* no effect. The positive value gives greenish tone and negative value gives
* purplish tone. The default value is 0o (00h). This is effective only on NTSC
* system. The default is 00h.
*/
#define TW5864_INDIR_VIN_7_HUE(channel) (0x007 + channel * 0x010)
#define TW5864_INDIR_VIN_8(channel) (0x008 + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_8 */
/*
* This bit controls the center frequency of the peaking filter.
* The corresponding gain adjustment is HFLT.
* 0 Low
* 1 center
*/
#define TW5864_INDIR_VIN_8_SCURVE BIT(7)
/* CTI level selection. The default is 1.
* 0 None
* 3 Highest
*/
#define TW5864_INDIR_VIN_8_CTI_SHIFT 4
#define TW5864_INDIR_VIN_8_CTI (0x03 << 4)
/*
* These bits control the amount of sharpness enhancement on the luminance
* signals. There are 16 levels of control with "0" having no effect on the
* output image. 1 through 15 provides sharpness enhancement with "F" being the
* strongest. The default is 1.
*/
#define TW5864_INDIR_VIN_8_SHARPNESS 0x0f
/*
* These bits control the luminance contrast gain. A value of 100 (64h) has a
* gain of 1. The range adjustment is from 0% to 255% at 1% per step. The
* default is 64h.
*/
#define TW5864_INDIR_VIN_9_CNTRST(channel) (0x009 + channel * 0x010)
/*
* These bits control the brightness. They have value of -128 to 127 in 2's
* complement form. Positive value increases brightness. A value 0 has no
* effect on the data. The default is 00h.
*/
#define TW5864_INDIR_VIN_A_BRIGHT(channel) (0x00a + channel * 0x010)
/*
* These bits control the digital gain adjustment to the U (or Cb) component of
* the digital video signal. The color saturation can be adjusted by adjusting
* the U and V color gain components by the same amount in the normal
* situation. The U and V can also be adjusted independently to provide greater
* flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has
* gain of 100%. The default is 80h.
*/
#define TW5864_INDIR_VIN_B_SAT_U(channel) (0x00b + channel * 0x010)
/*
* These bits control the digital gain adjustment to the V (or Cr) component of
* the digital video signal. The color saturation can be adjusted by adjusting
* the U and V color gain components by the same amount in the normal
* situation. The U and V can also be adjusted independently to provide greater
* flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has
* gain of 100%. The default is 80h.
*/
#define TW5864_INDIR_VIN_C_SAT_V(channel) (0x00c + channel * 0x010)
/* Read-only */
#define TW5864_INDIR_VIN_D(channel) (0x00d + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_D */
/* Macrovision color stripe detection may be un-reliable */
#define TW5864_INDIR_VIN_D_CSBAD BIT(3)
/* Macrovision AGC pulse detected */
#define TW5864_INDIR_VIN_D_MCVSN BIT(2)
/* Macrovision color stripe protection burst detected */
#define TW5864_INDIR_VIN_D_CSTRIPE BIT(1)
/*
* This bit is valid only when color stripe protection is detected, i.e. if
* CSTRIPE=1,
* 1 Type 2 color stripe protection
* 0 Type 3 color stripe protection
*/
#define TW5864_INDIR_VIN_D_CTYPE2 BIT(0)
/* Read-only */
#define TW5864_INDIR_VIN_E(channel) (0x00e + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_E */
/*
* Read-only.
* 0 Idle
* 1 Detection in progress
*/
#define TW5864_INDIR_VIN_E_DETSTUS BIT(7)
/*
* STDNOW Current standard invoked
* 0 NTSC (M)
* 1 PAL (B, D, G, H, I)
* 2 SECAM
* 3 NTSC4.43
* 4 PAL (M)
* 5 PAL (CN)
* 6 PAL 60
* 7 Not valid
*/
#define TW5864_INDIR_VIN_E_STDNOW_SHIFT 4
#define TW5864_INDIR_VIN_E_STDNOW (0x07 << 4)
/*
* 1 Disable the shadow registers
* 0 Enable VACTIVE and HDELAY shadow registers value depending on STANDARD.
* (Default)
*/
#define TW5864_INDIR_VIN_E_ATREG BIT(3)
/*
* STANDARD Standard selection
* 0 NTSC (M)
* 1 PAL (B, D, G, H, I)
* 2 SECAM
* 3 NTSC4.43
* 4 PAL (M)
* 5 PAL (CN)
* 6 PAL 60
* 7 Auto detection (Default)
*/
#define TW5864_INDIR_VIN_E_STANDARD 0x07
#define TW5864_INDIR_VIN_F(channel) (0x00f + channel * 0x010)
/* Define controls in register TW5864_INDIR_VIN_F */
/*
* 1 Writing 1 to this bit will manually initiate the auto format detection
* process. This bit is a self-clearing bit
* 0 Manual initiation of auto format detection is done. (Default)
*/
#define TW5864_INDIR_VIN_F_ATSTART BIT(7)
/* Enable recognition of PAL60 (Default) */
#define TW5864_INDIR_VIN_F_PAL60EN BIT(6)
/* Enable recognition of PAL (CN). (Default) */
#define TW5864_INDIR_VIN_F_PALCNEN BIT(5)
/* Enable recognition of PAL (M). (Default) */
#define TW5864_INDIR_VIN_F_PALMEN BIT(4)
/* Enable recognition of NTSC 4.43. (Default) */
#define TW5864_INDIR_VIN_F_NTSC44EN BIT(3)
/* Enable recognition of SECAM. (Default) */
#define TW5864_INDIR_VIN_F_SECAMEN BIT(2)
/* Enable recognition of PAL (B, D, G, H, I). (Default) */
#define TW5864_INDIR_VIN_F_PALBEN BIT(1)
/* Enable recognition of NTSC (M). (Default) */
#define TW5864_INDIR_VIN_F_NTSCEN BIT(0)
/* Some registers skipped. */
/* Use falling edge to sample VD1-VD4 from 54 MHz to 108 MHz */
#define TW5864_INDIR_VD_108_POL 0x041
#define TW5864_INDIR_VD_108_POL_VD12 BIT(0)
#define TW5864_INDIR_VD_108_POL_VD34 BIT(1)
#define TW5864_INDIR_VD_108_POL_BOTH \
(TW5864_INDIR_VD_108_POL_VD12 | TW5864_INDIR_VD_108_POL_VD34)
/* Some registers skipped. */
/*
* Audio Input ADC gain control
* 0 0.25
* 1 0.31
* 2 0.38
* 3 0.44
* 4 0.50
* 5 0.63
* 6 0.75
* 7 0.88
* 8 1.00 (default)
* 9 1.25
* 10 1.50
* 11 1.75
* 12 2.00
* 13 2.25
* 14 2.50
* 15 2.75
*/
/* [3:0] channel 0, [7:4] channel 1 */
#define TW5864_INDIR_AIGAIN1 0x060
/* [3:0] channel 2, [7:4] channel 3 */
#define TW5864_INDIR_AIGAIN2 0x061
/* Some registers skipped */
#define TW5864_INDIR_AIN_0x06D 0x06d
/* Define controls in register TW5864_INDIR_AIN_0x06D */
/*
* LAWMD Select u-Law/A-Law/PCM/SB data output format on ADATR and ADATM pin.
* 0 PCM output (default)
* 1 SB (Signed MSB bit in PCM data is inverted) output
* 2 u-Law output
* 3 A-Law output
*/
#define TW5864_INDIR_AIN_LAWMD_SHIFT 6
#define TW5864_INDIR_AIN_LAWMD (0x03 << 6)
/*
* Disable the mixing ratio value for all audio.
* 0 Apply individual mixing ratio value for each audio (default)
* 1 Apply nominal value for all audio commonly
*/
#define TW5864_INDIR_AIN_MIX_DERATIO BIT(5)
/*
* Enable the mute function for audio channel AINn when n is 0 to 3. It effects
* only for mixing. When n = 4, it enable the mute function of the playback
* audio input. It effects only for single chip or the last stage chip
* 0 Normal
* 1 Muted (default)
*/
#define TW5864_INDIR_AIN_MIX_MUTE 0x1f
/* Some registers skipped */
#define TW5864_INDIR_AIN_0x0E3 0x0e3
/* Define controls in register TW5864_INDIR_AIN_0x0E3 */
/*
* ADATP signal is coming from external ADPCM decoder, instead of on-chip ADPCM
* decoder
*/
#define TW5864_INDIR_AIN_0x0E3_EXT_ADATP BIT(7)
/* ACLKP output signal polarity inverse */
#define TW5864_INDIR_AIN_0x0E3_ACLKPPOLO BIT(6)
/*
* ACLKR input signal polarity inverse.
* 0 Not inversed (Default)
* 1 Inversed
*/
#define TW5864_INDIR_AIN_0x0E3_ACLKRPOL BIT(5)
/*
* ACLKP input signal polarity inverse.
* 0 Not inversed (Default)
* 1 Inversed
*/
#define TW5864_INDIR_AIN_0x0E3_ACLKPPOLI BIT(4)
/*
* ACKI [21:0] control automatic set up with AFMD registers
* This mode is only effective when ACLKRMASTER=1
* 0 ACKI [21:0] registers set up ACKI control
* 1 ACKI control is automatically set up by AFMD register values
*/
#define TW5864_INDIR_AIN_0x0E3_AFAUTO BIT(3)
/*
* AFAUTO control mode
* 0 8kHz setting (Default)
* 1 16kHz setting
* 2 32kHz setting
* 3 44.1kHz setting
* 4 48kHz setting
*/
#define TW5864_INDIR_AIN_0x0E3_AFMD 0x07
#define TW5864_INDIR_AIN_0x0E4 0x0e4
/* Define controls in register TW5864_INDIR_AIN_0x0ED */
/*
* 8bit I2S Record output mode.
* 0 L/R half length separated output (Default).
* 1 One continuous packed output equal to DSP output format.
*/
#define TW5864_INDIR_AIN_0x0E4_I2S8MODE BIT(7)
/*
* Audio Clock Master ACLKR output wave format.
* 0 High periods is one 27MHz clock period (default).
* 1 Almost duty 50-50% clock output on ACLKR pin. If this mode is selected, two
* times bigger number value need to be set up on the ACKI register. If
* AFAUTO=1, ACKI control is automatically set up even if MASCKMD=1.
*/
#define TW5864_INDIR_AIN_0x0E4_MASCKMD BIT(6)
/* Playback ACLKP/ASYNP/ADATP input data MSB-LSB swapping */
#define TW5864_INDIR_AIN_0x0E4_PBINSWAP BIT(5)
/*
* ASYNR input signal delay.
* 0 No delay
* 1 Add one 27MHz period delay in ASYNR signal input
*/
#define TW5864_INDIR_AIN_0x0E4_ASYNRDLY BIT(4)
/*
* ASYNP input signal delay.
* 0 no delay
* 1 add one 27MHz period delay in ASYNP signal input
*/
#define TW5864_INDIR_AIN_0x0E4_ASYNPDLY BIT(3)
/*
* ADATP input data delay by one ACLKP clock.
* 0 No delay (Default). This is for I2S type 1T delay input interface.
* 1 Add 1 ACLKP clock delay in ADATP input data. This is for left-justified
* type 0T delay input interface.
*/
#define TW5864_INDIR_AIN_0x0E4_ADATPDLY BIT(2)
/*
* Select u-Law/A-Law/PCM/SB data input format on ADATP pin.
* 0 PCM input (Default)
* 1 SB (Signed MSB bit in PCM data is inverted) input
* 2 u-Law input
* 3 A-Law input
*/
#define TW5864_INDIR_AIN_0x0E4_INLAWMD 0x03
/*
* Enable state register updating and interrupt request of audio AIN5 detection
* for each input
*/
#define TW5864_INDIR_AIN_A5DETENA 0x0e5
/* Some registers skipped */
/*
* [7:3]: DEV_ID The TW5864 product ID code is 01000
* [2:0]: REV_ID The revision number is 0h
*/
#define TW5864_INDIR_ID 0x0fe
#define TW5864_INDIR_IN_PIC_WIDTH(channel) (0x200 + 4 * channel)
#define TW5864_INDIR_IN_PIC_HEIGHT(channel) (0x201 + 4 * channel)
#define TW5864_INDIR_OUT_PIC_WIDTH(channel) (0x202 + 4 * channel)
#define TW5864_INDIR_OUT_PIC_HEIGHT(channel) (0x203 + 4 * channel)
/* Some registers skipped */
#define TW5864_INDIR_CROP_ETC 0x260
/* Define controls in register TW5864_INDIR_CROP_ETC */
/* Enable cropping from 720 to 704 */
#define TW5864_INDIR_CROP_ETC_CROP_EN 0x4
/*
* Interrupt status register from the front-end. Write "1" to each bit to clear
* the interrupt
* 15:0 Motion detection interrupt for channel 0 ~ 15
* 31:16 Night detection interrupt for channel 0 ~ 15
* 47:32 Blind detection interrupt for channel 0 ~ 15
* 63:48 No video interrupt for channel 0 ~ 15
* 79:64 Line mode underflow interrupt for channel 0 ~ 15
* 95:80 Line mode overflow interrupt for channel 0 ~ 15
*/
/* 0x2d0~0x2d7: [63:0] bits */
#define TW5864_INDIR_INTERRUPT1 0x2d0
/* 0x2e0~0x2e3: [95:64] bits */
#define TW5864_INDIR_INTERRUPT2 0x2e0
/*
* Interrupt mask register for interrupts in 0x2d0 ~ 0x2d7
* 15:0 Motion detection interrupt for channel 0 ~ 15
* 31:16 Night detection interrupt for channel 0 ~ 15
* 47:32 Blind detection interrupt for channel 0 ~ 15
* 63:48 No video interrupt for channel 0 ~ 15
* 79:64 Line mode underflow interrupt for channel 0 ~ 15
* 95:80 Line mode overflow interrupt for channel 0 ~ 15
*/
/* 0x2d8~0x2df: [63:0] bits */
#define TW5864_INDIR_INTERRUPT_MASK1 0x2d8
/* 0x2e8~0x2eb: [95:64] bits */
#define TW5864_INDIR_INTERRUPT_MASK2 0x2e8
/* [11:0]: Interrupt summary register for interrupts & interrupt mask from in
* 0x2d0 ~ 0x2d7 and 0x2d8 ~ 0x2df
* bit 0: interrupt occurs in 0x2d0 & 0x2d8
* bit 1: interrupt occurs in 0x2d1 & 0x2d9
* bit 2: interrupt occurs in 0x2d2 & 0x2da
* bit 3: interrupt occurs in 0x2d3 & 0x2db
* bit 4: interrupt occurs in 0x2d4 & 0x2dc
* bit 5: interrupt occurs in 0x2d5 & 0x2dd
* bit 6: interrupt occurs in 0x2d6 & 0x2de
* bit 7: interrupt occurs in 0x2d7 & 0x2df
* bit 8: interrupt occurs in 0x2e0 & 0x2e8
* bit 9: interrupt occurs in 0x2e1 & 0x2e9
* bit 10: interrupt occurs in 0x2e2 & 0x2ea
* bit 11: interrupt occurs in 0x2e3 & 0x2eb
*/
#define TW5864_INDIR_INTERRUPT_SUMMARY 0x2f0
/* Motion / Blind / Night Detection */
/* valid value for channel is [0:15] */
#define TW5864_INDIR_DETECTION_CTL0(channel) (0x300 + channel * 0x08)
/* Define controls in register TW5864_INDIR_DETECTION_CTL0 */
/*
* Disable the motion and blind detection.
* 0 Enable motion and blind detection (default)
* 1 Disable motion and blind detection
*/
#define TW5864_INDIR_DETECTION_CTL0_MD_DIS BIT(5)
/*
* Request to start motion detection on manual trigger mode
* 0 None Operation (default)
* 1 Request to start motion detection
*/
#define TW5864_INDIR_DETECTION_CTL0_MD_STRB BIT(3)
/*
* Select the trigger mode of motion detection
* 0 Automatic trigger mode of motion detection (default)
* 1 Manual trigger mode for motion detection
*/
#define TW5864_INDIR_DETECTION_CTL0_MD_STRB_EN BIT(2)
/*
* Define the threshold of cell for blind detection.
* 0 Low threshold (More sensitive) (default)
* : :
* 3 High threshold (Less sensitive)
*/
#define TW5864_INDIR_DETECTION_CTL0_BD_CELSENS 0x03
#define TW5864_INDIR_DETECTION_CTL1(channel) (0x301 + channel * 0x08)
/* Define controls in register TW5864_INDIR_DETECTION_CTL1 */
/*
* Control the temporal sensitivity of motion detector.
* 0 More Sensitive (default)
* : :
* 15 Less Sensitive
*/
#define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS_SHIFT 4
#define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS (0x0f << 4)
/*
* Adjust the horizontal starting position for motion detection
* 0 0 pixel (default)
* : :
* 15 15 pixels
*/
#define TW5864_INDIR_DETECTION_CTL1_MD_PIXEL_OS 0x0f
#define TW5864_INDIR_DETECTION_CTL2(channel) (0x302 + channel * 0x08)
/* Define controls in register TW5864_INDIR_DETECTION_CTL2 */
/*
* Control the updating time of reference field for motion detection.
* 0 Update reference field every field (default)
* 1 Update reference field according to MD_SPEED
*/
#define TW5864_INDIR_DETECTION_CTL2_MD_REFFLD BIT(7)
/*
* Select the field for motion detection.
* 0 Detecting motion for only odd field (default)
* 1 Detecting motion for only even field
* 2 Detecting motion for any field
* 3 Detecting motion for both odd and even field
*/
#define TW5864_INDIR_DETECTION_CTL2_MD_FIELD_SHIFT 5
#define TW5864_INDIR_DETECTION_CTL2_MD_FIELD (0x03 << 5)
/*
* Control the level sensitivity of motion detector.
* 0 More sensitive (default)
* : :
* 15 Less sensitive
*/
#define TW5864_INDIR_DETECTION_CTL2_MD_LVSENS 0x1f
#define TW5864_INDIR_DETECTION_CTL3(channel) (0x303 + channel * 0x08)
/* Define controls in register TW5864_INDIR_DETECTION_CTL3 */
/*
* Define the threshold of sub-cell number for motion detection.
* 0 Motion is detected if 1 sub-cell has motion (More sensitive) (default)
* 1 Motion is detected if 2 sub-cells have motion
* 2 Motion is detected if 3 sub-cells have motion
* 3 Motion is detected if 4 sub-cells have motion (Less sensitive)
*/
#define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS_SHIFT 6
#define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS (0x03 << 6)
/*
* Control the velocity of motion detector.
* Large value is suitable for slow motion detection.
* In MD_DUAL_EN = 1, MD_SPEED should be limited to 0 ~ 31.
* 0 1 field intervals (default)
* 1 2 field intervals
* : :
* 61 62 field intervals
* 62 63 field intervals
* 63 Not supported
*/
#define TW5864_INDIR_DETECTION_CTL3_MD_SPEED 0x3f
#define TW5864_INDIR_DETECTION_CTL4(channel) (0x304 + channel * 0x08)
/* Define controls in register TW5864_INDIR_DETECTION_CTL4 */
/*
* Control the spatial sensitivity of motion detector.
* 0 More Sensitive (default)
* : :
* 15 Less Sensitive
*/
#define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS_SHIFT 4
#define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS (0x0f << 4)
/*
* Define the threshold of level for blind detection.
* 0 Low threshold (More sensitive) (default)
* : :
* 15 High threshold (Less sensitive)
*/
#define TW5864_INDIR_DETECTION_CTL4_BD_LVSENS 0x0f
#define TW5864_INDIR_DETECTION_CTL5(channel) (0x305 + channel * 0x08)
/*
* Define the threshold of temporal sensitivity for night detection.
* 0 Low threshold (More sensitive) (default)
* : :
* 15 High threshold (Less sensitive)
*/
#define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS_SHIFT 4
#define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS (0x0f << 4)
/*
* Define the threshold of level for night detection.
* 0 Low threshold (More sensitive) (default)
* : :
* 3 High threshold (Less sensitive)
*/
#define TW5864_INDIR_DETECTION_CTL5_ND_LVSENS 0x0f
/*
* [11:0] The base address of the motion detection buffer. This address is in
* unit of 64K bytes. The generated DDR address will be {MD_BASE_ADDR,
* 16"h0000}. The default value should be 12"h000
*/
#define TW5864_INDIR_MD_BASE_ADDR 0x380
/*
* This controls the channel of the motion detection result shown in register
* 0x3a0 ~ 0x3b7. Before reading back motion result, always set this first.
*/
#define TW5864_INDIR_RGR_MOTION_SEL 0x382
/* [15:0] MD strobe has been performed at channel n (read only) */
#define TW5864_INDIR_MD_STRB 0x386
/* NO_VIDEO Detected from channel n (read only) */
#define TW5864_INDIR_NOVID_DET 0x388
/* Motion Detected from channel n (read only) */
#define TW5864_INDIR_MD_DET 0x38a
/* Blind Detected from channel n (read only) */
#define TW5864_INDIR_BD_DET 0x38c
/* Night Detected from channel n (read only) */
#define TW5864_INDIR_ND_DET 0x38e
/* 192 bit motion flag of the channel specified by RGR_MOTION_SEL in 0x382 */
#define TW5864_INDIR_MOTION_FLAG 0x3a0
#define TW5864_INDIR_MOTION_FLAG_BYTE_COUNT 24
/*
* [9:0] The motion cell count of a specific channel selected by 0x382. This is
* for DI purpose
*/
#define TW5864_INDIR_MD_DI_CNT 0x3b8
/* The motion detection cell sensitivity for DI purpose */
#define TW5864_INDIR_MD_DI_CELLSENS 0x3ba
/* The motion detection threshold level for DI purpose */
#define TW5864_INDIR_MD_DI_LVSENS 0x3bb
/* 192 bit motion mask of the channel specified by MASK_CH_SEL in 0x3fe */
#define TW5864_INDIR_MOTION_MASK 0x3e0
#define TW5864_INDIR_MOTION_MASK_BYTE_COUNT 24
/* [4:0] The channel selection to access masks in 0x3e0 ~ 0x3f7 */
#define TW5864_INDIR_MASK_CH_SEL 0x3fe
/* Clock PLL / Analog IP Control */
/* Some registers skipped */
#define TW5864_INDIR_DDRA_DLL_DQS_SEL0 0xee6
#define TW5864_INDIR_DDRA_DLL_DQS_SEL1 0xee7
#define TW5864_INDIR_DDRA_DLL_CLK90_SEL 0xee8
#define TW5864_INDIR_DDRA_DLL_TEST_SEL_AND_TAP_S 0xee9
#define TW5864_INDIR_DDRB_DLL_DQS_SEL0 0xeeb
#define TW5864_INDIR_DDRB_DLL_DQS_SEL1 0xeec
#define TW5864_INDIR_DDRB_DLL_CLK90_SEL 0xeed
#define TW5864_INDIR_DDRB_DLL_TEST_SEL_AND_TAP_S 0xeee
#define TW5864_INDIR_RESET 0xef0
#define TW5864_INDIR_RESET_VD BIT(7)
#define TW5864_INDIR_RESET_DLL BIT(6)
#define TW5864_INDIR_RESET_MUX_CORE BIT(5)
#define TW5864_INDIR_PV_VD_CK_POL 0xefd
#define TW5864_INDIR_PV_VD_CK_POL_PV(channel) BIT(channel)
#define TW5864_INDIR_PV_VD_CK_POL_VD(channel) BIT(channel + 4)
#define TW5864_INDIR_CLK0_SEL 0xefe
#define TW5864_INDIR_CLK0_SEL_VD_SHIFT 0
#define TW5864_INDIR_CLK0_SEL_VD_MASK 0x3
#define TW5864_INDIR_CLK0_SEL_PV_SHIFT 2
#define TW5864_INDIR_CLK0_SEL_PV_MASK (0x3 << 2)
#define TW5864_INDIR_CLK0_SEL_PV2_SHIFT 4
#define TW5864_INDIR_CLK0_SEL_PV2_MASK (0x3 << 4)